Filter
Top Products
74 SPX2000—Owner’s Manual
■Fine parameters
Effect list
■Basic parameters
■Fine parameters
Parameter name Range Explanation
MIX BAL. 0—100%
Balance between the original sound and effect sound. At a setting of 0% only the original sound
will be output; at a setting of 100% only the effect sound will be output.
OUT LVL 0—100%
Output level after the original sound and effect sound have been mixed.
Decrease this value if you want to lower the output. At a setting of 0% there will be no output.
ER NUM. 1—19
The number of early reflections. Increasing this value will increase the number of reflections.
HPF Thru, 21.2 Hz—8.00 kHz
A filter that cuts the low-frequency portion of the effect. Frequency components lower than the
frequency specified here will be cut. With a setting of Thru this filter will do nothing. This filter
does not affect the original sound.
LPF 50.0 Hz—16.0 kHz, Thru
A filter that cuts the high-frequency portion of the effect. Frequency components above the fre-
quency specified here will be cut. With a setting of Thru this filter will do nothing. This filter does
not affect the original sound.
DLY/ER 0—100%
(Delay + Early Reflection only) This is the balance between delay and early reflections. If this value
is 0% only the delay sound will be output; if this is 100% only the early reflections will be output.
DLY.BAL 0—100%
(Delay -> Early Reflection only) This specifies the amount of early reflections. Raising this value
will strengthen the early reflections. If this value is 0% only delay will be produced.
SYNC ON, OFF
Switches tempo synchronization on/off. If this is ON, the delays will synchronize to the tempo syn-
chronization source specified by “TEMPO SOURCE” (page 23). Each NOTE value will be set to the
synchronized tempo value.
NOTE L
NOTE R
NOTE FB
*a
*a.
These parameters are used for tempo synchronization. If SYNC is ON, each DELAY value will be set
according to the corresponding NOTE value and TEMPO. If SYNC is OFF, this value is ignored.
TEMPO 25—300
This parameter is used for tempo synchronization. If SYNC is ON, the various DELAY values will be set
according to this value and the corresponding NOTE values. If SYNC is OFF, this value is ignored.
No. Effect name TYPE ROOMSIZE LIVENESS INI.DLY DIFF. DENSITY DELAY L DELAY R FB.DLY
90 DELAY+ER 1 S-Hall 10.2 3 10.2 ms 8 64% 250.0 ms 500.0 ms 500.0 ms
91 DELAY+ER 2 L-Hall 1.4 3 17.0 ms 10 68% 24.5 ms 15.5 ms 77.6 ms
92 DELAY->ER 1 Spring 1.8 3 9.0 ms 8 90% 250.0 ms 375.0 ms 500.0 ms
93 DELAY->ER 2 S-Hall 1.8 3 30.4 ms 10 82% 27.3 ms 15.6 ms 12.2 ms
No. Effect name FB.GAIN HI.RATIO
90 DELAY+ER 1 +24% 0.4
91 DELAY+ER 2 –50% 0.4
92 DELAY->ER 1 –45% 0.3
93 DELAY->ER 2 –42% 0.6
No. Effect name MIX BAL. OUT LVL ER NUM. HPF LPF DLY/ER DLY.BAL
90 DELAY+ER 1 100% 100% 14 80.0 Hz 7.10 kHz 50%
91 DELAY+ER 2 100% 100% 16 Thru 12.5 kHz 37%
92 DELAY->ER 1 100% 100% 14 132 Hz 4.75 kHz 35%
93 DELAY->ER 2 100% 100% 19 Thru 11.2 kHz
30%
No. Effect name SYNC NOTE L NOTE R NOTE FB TEMPO
90 DELAY+ER 1 OFF —
91 DELAY+ER 2 OFF —
92 DELAY->ER 1 OFF —
93 DELAY->ER 2 OFF —