Filter
Top Products
78 SPX2000—Owner’s Manual
■Fine parameters
Effect list
The following tables show the default parameter values for the effect belonging to the Freeze type (PRESET bank).
■Basic parameters
■Fine parameters
Freeze A (CLASSIC bank)
This is a freeze effect based on earlier models of the SPX series. You can specify the start/end points of the playback. The
parameter structure is simpler than the corresponding effect of the PRESET bank.
Each aspect of the sound is controlled by the following effect parameters.
Recording: REC MODE, TRG. DLY, RECORD
Playback: PLAY, START, END
Recording trigger: INP. TRG
Output level: OUT LVL, MIX BAL.
Parameter details
■Basic parameters
Parameter name Range Explanation
MIX BAL. 0—100%
Balance between the original sound and effect sound. At a setting of 0% only the original sound
will be output; at a setting of 100% only the effect sound will be output.
OUT LVL 0—100%
Output level after the original sound and effect sound have been mixed. Decrease this value if you
want to lower the output. At a setting of 0% there will be no output.
FINE –50—+50
Amount of pitch change for the playback, in units of one cent (1/100th of a semitone). Positive (+)
settings will raise the playback pitch higher than the original, and negative (–) settings will lower it.
TRG MASK 0—1000 ms
The time from when a trigger is received until the next trigger will be allowed.
No. Effect name REC MODE REC DLY RECORD PLAY PLY MODE START END LOOP LOOP NUM
97 FREEZE
MANUAL –50 ms — — CONTI. 0.0 ms
*a
*a. At 44.1 kHz or 88.2 kHz, this will be 2970.5 ms. At 48 kHz or 96 kHz, this will be 2729.2 ms.
0.0 ms 100
PITCH MIDI TRG TRG LVL
0 OFF –14 dB
No. Effect name MIX BAL. OUT LVL FINE TRG MASK
97 FREEZE 100% 100% 0 1000 ms
Parameter name Range Explanation
REC MODE MANUAL, AUTO
Recording method. Choose MANUAL (manual) or AUTO (automatic).
TRG. DLY –1000—+1000 ms
Delay from when recording is triggered until recording actually begins.
INP. TRG ON, OFF
This setting specifies whether the input signal will trigger the playback. If this is ON, an input sig-
nal of –14 dB or higher will trigger the playback. If this is OFF, you can start playback by pressing
the [▲ INC] or [▼ DEC] button or by operating a MIDI device.
RECORD ---
When REC MODE is MANUAL, press the [▼ DEC] button (G) to enter record-ready mode; then
press the [▲ INC] button (G) to begin recording.
PLAY ---
If INP.TRG is OFF, pressing the [▲ INC] or [▼ DEC] buttons (G) will start playback.
START
*a
*a. At 44.1 kHz or 88.2 kHz, this will be 0.0—2970.5 ms. At 48 kHz or 96 kHz, this will be 0.0—2729.2 ms.
Playback start point for the sampled data.
END
*a
Playback end point for the sampled data.
OUT LVL 0—100%
Output level after the original sound and effect sound have been mixed. Decrease this value if you
want to lower the output. At a setting of 0% there will be no output.
MIX BAL. 0—100%
Balance between the original sound and effect sound. At a setting of 0% only the original sound
will be output; at a setting of 100% only the effect sound will be output.