Filter
Top Products
Using the Performance Mode
E-64
Editable Parameter List
Editable Performance Parameter List
Display Description Settings
Zone Parame >Ent
Zone parameters. This group includes parameters for each of the zones (Zone 1 through 4).
• Use the
9
PART minus (–), plus (+) buttons to select the zone you want to edit.
• You also can enter the group using the following shortcut: Perform step 2 under “To register a
performance” (page E-62) and then hold down
7
EDIT. This will enter the group.
Zone
Zone on/off. Turns all zones on or off This setting is different from the mixer function page (page
E-68) part on/off (Part Enable) setting.
Off, On
Tone
Tone. Selects the tone for each zone. This setting is the same as the mixer function part tone
(page E-68).
• While this item is selected, you can select a tone using the same operation as that used in the
Tone Mode.
• This setting can also be configured using quick editing (page E-16).
• There are some limitations on the selection of tone categories for Zones 2 through 4 (page
E-16).
• A tone with DSP will have DSP next to the tone name on the display (page E-37).
Zone 1:
Solo Synth P00 to
Various U29
Zone 2 to 4:
Piano P00 to
Various U29
KeyRangLow
Key range low. Specifies the low key range of the keyboard for each zone. This setting is used in
combination with the Key Range Hi setting to configure key ranges for each zone.
For example, configuring F3 (low) to C7 (high) for Zones 1 and 2 and C2 (low) to E3 (high) for
Zones 3 and 4 will enable play of Zone 1 and 2 tones on the right side keyboard range in the
illustration below, and the Zone 3 and 4 tones on the left side keyboard.
• Setting can be specified using the keyboard keys.
C-1 to G9
KeyRangHi
Key range high. Specifies the high range of the keyboard for each zone. This setting is used in
combination with the Key Range Lo setting to configure key ranges for each zone.
C-1 to G9
Volume Volume. This setting is the same as the mixer function tone volume (page E-68). 0 to 127
Pan
Pan. Adjusts the left-right position of sound in the stereo field. This setting is the same as the
mixer function part panning (page E-68).
–64 to 0 to +63
Oct.Shift Octave shift. Shifts the tone of notes by octave units. –2 to 0 to +2
Transpose
Transpose. Shifts the tone of notes by semitone units. This setting is the same as the mixer
function part coarse tune (page E-68).
–12 to 0 to +12
FineTune Fine tune. This setting is the same as the mixer function part fine tune (page E-68). –99 to 0 to +99
BendRngDwn Bend range down. Pitch change amount for downward bender operation. 0 to 24
BendRngUp Bend range up. Pitch change amount for upward bender operation. 0 to 24
Rev Send Reverb send. This setting is the same as the mixer reverb send (page E-68). 0 to 127
Cho Send Chorus send. This setting is the same as the mixer chorus send (page E-68). 0 to 127
DSP Line DSP line. This setting is the same as the mixer function part DSP line (page E-68). Off, On
Knob1Enable Knob 1 on/off. Enables/disables
3
K1 operation for each zone. Off, On
Knob2Enable Knob 2 on/off. Enables/disables
3
K2 operation for each zone. Off, On
Knob3Enable Knob 3 on/off. Enables/disables
3
K3 operation for each zone. Off, On
Knob4Enable Knob 4 on/off. Enables/disables
3
K4 operation for each zone. Off, On
Bend Enable Bender on/off. Enables/disables
bs
BENDER operation for each zone. Off, On
Wheel Enable Modulation wheel on/off. Enables/disables
bs
MODULATION operation for each zone. Off, On
Pedal Enable
Pedal on/off. Enables/disables operation of a pedal plugged in to the
ck
SUSTAIN/
ASSIGNABLE JACK for each Zone.
Off, On
C2 F3E3 C7
Zone 3
Zone 4
Zone 1
Zone 2