Filter
Top Products
Using a Memory Card
E-75
• Format a memory card before using it for the first time.
• Before formatting a memory card, make sure it does
not have any valuable data stored on it.
• The memory card format operation performed by this
Synthesizer is a “quick format”. If you want to
completely delete all of the data on the memory card,
format it on your computer or some other device.
1.
Insert the memory card you want to format into
the Synthesizer’s card slot.
• Make sure the memory card is write-enabled. Check
the position of the card’s write-protect switch to ensure
it is not in the write-protect position.
2.
Press
7
SETTING.
3.
Use the
bq
up (q) and down (w) buttons to
move the item selection cursor (0) to
“CardUtility” and then press
bq
ENTER.
• This causes the “CARD UTIL” screen to appear.
4.
Use the
bq
up (q) and down (w) buttons to
move the item selection cursor (0) to “Format”.
5.
Press the
bq
ENTER button.
• This will cause the confirmation message “Sure?” to
appear.
6.
Press the
bq
YES button to format the memory
card or the
bq
NO button to cancel.
• The message “Please Wait” will remain on the display
while the format operation is being performed. Do not
perform any Synthesizer operation while this message
is on the display. “Complete!” appears on the display
after formatting is complete.
• Formatting may take as long as a few minutes to
complete.
1.
Insert the memory card into the card slot.
2.
Depending on the type of data you want to save
to the memory card, perform one of the steps
shown below.
Formatting a Memory Card Saving Synthesizer Data to a
Memory Card
To save Synthesizer data to a memory card
To save this
type of data:
Perform these steps:
One user
performance
1. Press
7
PERFORM.
2. Press
bq
MENU.
One user PCM
melody tone
1. Press
7
TONE.
2. Press one of the
bl
PIANO to VARIOUS
buttons to select a melody tone.
3. Press
bq
MENU.
One user drawbar
organ tone.
1. Press
7
TONE.
2. Press
bl
DRAWBAR ORGAN.
3. Press
bq
MENU.
One user hex layer
tones
1. Press
7
TONE.
2. Press
bl
HEX LAYER.
3. Press
bq
MENU.
One user Solo
Synthesizer tone
1. Press
7
TONE.
2. Press
bl
SOLO SYNTH.
3. Press
bq
MENU.
One user PCM
drum tone
1. Press
7
TONE.
2. Press
bl
VARIOUS and then select the
drum tone.
3. Press
bq
MENU.
One user DSP 1. Hold down
bm
MIXER until the EFFECT
screen appears on the display.
2. Use the
bq
cursor (U, q, w, I) buttons
to move the item selection cursor (0) to
“DSP Select” and then press
bq
ENTER.
• “Ent” is not displayed in the case of a Solo
Synthesizer tone.
3. Press
bq
MENU.
One user step
sequence
1. Press
7
STEP SEQ.
2. Press
bq
MENU.
One step
sequence chain
1. Hold down
bk
CHAIN until the CHAIN
screen appears on the display.
2. Press
bq
MENU.
One user phrase 1. Hold down
bn
KEY PLAY until the PHRASE
screen appears on the display.
2. Press
bq
MENU.
One user arpeggio 1. Hold down
bm
ARPEGGIO until the
ARPEGGIO screen appears on the display.
2. Press
bq
MENU.
All data 1. Press
7
SETTING.
2. Use the
bq
up (q) and down (w)
buttons to move the item selection cursor
(0) to “CardUtility” and then press
bq
ENTER.
3. Use the
bq
up (q) and down (w)
buttons to move the item selection cursor
(0) to “All data” and then press
bq
ENTER.