Filter
Top Products
Command and Response Table for DSP SIS Commands (continued)
Command ASCII command
(host to device)
Response
(device to host)
Additional description
Audio group master commands
NOTE: •See Group Masters on page69, for more information about audio group masters.
•Agroupmusthaveassignedmembers for these commands to have an effect.
•For
X6^
, a positive (+) value is assumed unless a negative (–) value is specified.
•Ifenteringa
X6^
value outside the valid range for the group or outside the soft limits, the DMP64
responds with an “invalid parameter” (E13) error.
•
X6^
,
X6&
, and
X6*
values can be sent without leading zeroes; responses are always 5 digits.
Set a group fader control
E
D
X6%
*
X6^
GRPM
}
Grpm
X6%
*
X6^]
Set the group fader to a value
of
X6^
.
Example:
E
d2*-293*GRPM
}
GrpmD02*-00293
]
Set the group 2 fader control
to -29.3dB.
Raise a group fader control
E
D
X6%
*
X6&
+GRPM
}
Grpm
X6%
*
X6^]
Increase the level of the
X6%
group fader by
X6&
dB.
Example
E
d2*30+GRPM
}
GrpmD02*-00263
]
Raise the group 2 fader 3dB
(from -29.3dB to -26.3dB,
starting from the level set
in the “Set a group fader
control” example, above.
Lower a group fader control
E
D
X6%
*
X6&
-GRPM
}
Grpm
X6%
*
X6^]
Decrease the level of the
X6%
group fader by
X6&
dB.
View the group fader control
level
E
D
X6%
GRPM
}
Grpm
X6%
*
X6^]
In verbose modes 1 and 2, the
response is simplified to
X6^]
.
Mute a group mute control
E
D
X6%
*1GRPM
}
GrpmD
X6%
*+00001
]
Mute all blocks in group
X6%
.
Clear (unmute) a group
mute control
E
D
X6%
*0GRPM
}
GrpmD
X6%
*+00000
]
Umute all blocks in group
X6%
.
View a group mute control
E
D
X6%
GRPM
}
GrpmD
X6%
*
X6$]
For group masters,
X6$
is always expressed as a
positive or negative 5-digit
value.
Set soft limits
E
L
X6%
*
X6*
upper
*
X6*
lower
GRPM
}
Set the groups soft limits to
X6*
and
X6*
.
GrpmL
X6%
*
X6*
*
X6*]
Example:
E
L2
*
+60
*
-60GRPM
}
GrpmL02*+00060*-00060
]
Set the upper soft limit for the
group 2 fader to +6.0dB and
the lower limit to -6.0dB.
View soft limits
E
L
X6%
GRPM
}
GrpmL
X6%
*
X6*
*
X6*]
In verbose modes 0 and 1,
the response is simplified to
X6*
*
X6*]
.
View group type
E
P
X6%
GRPM
}
GrpmP
X6%
*
X6(]
Show the group type (
X6(
)
for group
X6%
. In verbose
modes 0 and 1, the response
is simplified to
X6(]
.
View group members
E
O
X6%
GRPM
}
GrpmO
X6%
*
X6)
1
*
X6)
2
*
...*
X6)
16
]
X6)
is the control or mix point.
In verbose modes 0 and 1,
the response is simplified to
X6)
1
*
X6)
2
*...*
X6)
16
]
.
NOTES:
X6)
= Audio level control, or mix-point
select
See Table 1 on page 111 and 112.
X6%
= Group master group number
01 - 32
X6^
= Group fader level
dB value, in 0.1dB increments, using negative numbers but not decimal
places. –100.0dB to +80.0dB is represented by –1000 to 800. The valid
range depends on the type of gain or trim block assigned to the group number
(
X6%
).
X6&
= Group fader increase/decrease
dB value, in 0.1dB increments, to raise or lower a group fader.
X6*
= Group fader soft limit
dB value, in 0.1dB increments. The valid range must be within the range for
the gain block grouped in
X6%
.
X6(
= Group type
6 = gain
12 = mute
DMP64 • SIS Programming and Control 106