Filter
Top Products
44
Value ....................... [–06...+06, –24...+24, –63...+63]
Modify the value that is recorded at each step.
These values are the amount of change that will be applied
to the value of the parameter that is assigned to the
sequence.
–06...+06
This is the range when “Knob” is set to Step Length.
–24...+24
This is the range when “Knob” is set to Pitch or OSC2
Semi.
–63...+63
This is the range for settings other than the above.
■ EFFECTS
These are the effect-related parameters.
A: Type............................. [Cho/Flg, Ensemble, Phaser]
Select the effect type.
Cho/Flg
This effect modulates the delay time of the input signal to
add depth and warmth to the sound. Increasing the
“Depth” value will produce a flanger effect.
Ensemble
This effect uses multiple chorus units to add three-dimen-
sional depth and spaciousness to the sound.
Phaser
This effect modulates the phase of the sound to create a
twisting sensation.
B: LFO Speed ❮ SPEED ❯ ..............................[000...127]
Specify the speed of the LFO inside the modulation effect.
C: Depth ❮ DEPTH/FEEDBACK ❯ ...................[000...127]
Specify the modulation depth and amount of feedback.
Increasing this value will deepen the modulation effect and
also increase the amount of feedback. If you do not wish to
apply the effect, set this to 000.
Excessively high settings of this parameter may cause
the output to be distorted.
A: Type.................................. [StereoDelay...L/R Delay]
Select the delay type.
StereoDelay
This is a stereo delay.
CrossDelay
This is a stereo delay where the left and right channels of
feedback are interchanged. On Dual programs, it is effec-
tive to set the panpot of the two timbres to left and right
respectively.
L/R Delay
This is a delay where the delay sound is output to left and
right alternately.
B: Tempo Sync..............................................[ON, OFF]
If this is ON, the delay time will synchronize to the tempo.
If the Global mode Page 3C: MIDI “Clock” setting is Inter-
nal, the delay time will synchronize to the tempo set by the
[TEMPO] knob. If it is External, the delay time will synchro-
nize to the MIDI clock received from an external MIDI
device.
C: Delay Time ❮ TIME ❯ ...............................[000...127]
Set the delay time.
This parameter will be displayed and can be set only if
“Tempo Sync” is OFF.
C: Sync Note ............................................ [1/32...1/1]
Specify the delay time as a proportion of the tempo set by
the [TEMPO] knob. (☞P.66 “How “Resolution” and “Sync
Note” values correspond to note values”)
This parameter will be displayed and can be set only if
“Tempo Sync” is ON.
D: Depth ❮ DEPTH/FEEDBACK ❯...................[000...127]
Specify the delay depth and feedback amount. Increasing
this value will make the delay louder and will also increase
the amount of feedback.
If you do not wish to apply a delay, set this to 000.
Excessively high settings of this parameter may cause
the output to be distorted.
A: LowEQFreq ....................................[40Hz...1000Hz]
Set the frequency of the low-range equalizer.
B: LowEQGain...................................... [–12.0...+12.0]
Set the gain of the low-range equalizer.
C: HiEQFreq ................................. [1.00kHz...18.0kHz]
Set the frequency of the high-range equalizer.
Page22: MOD FX
Page23: DELAY FX
Stereo Delay
DELAY
FEEDBACK
FEEDBACK
DELAY
Page24: EQ
Cross Delay
DELAY
FEEDBACK
FEEDBACK
DELAY
L/R Delay
DELAY
FEEDBACK
FEEDBACK
DELAY