Filter
Top Products
48
3 Use the [+/YES] [–/NO] keys to select the copy source
program.
4 Use the CURSOR [®] key to move the cursor to the
copy source timbre.
5 Use the [+/YES] [–/NO] keys to select the copy source
timbre.
If the copy source program is Single, it is not possible to
select the copy source timbre (only timbre 1 is available).
6 Use the CURSOR [®] key to move the cursor to the
copy source sequence.
7 Use the [+/YES] [–/NO] keys to select the copy source
sequence.
8 Use the CURSOR [®] to move the cursor to the copy
destination sequence.
9 Use the [+/YES] [–/NO] keys to select the copy destina-
tion sequence.
0 Use the CURSOR [®] key to move the cursor to “OK,”
and press the [+/YES] key.
You will be asked to confirm the copy function.
A Press the [+/YES] key once again.
The copy will be completed, and the display will indi-
cate “Completed.”
B Press the [EXIT] key.
You will return to the first screen of the “CopySeq” func-
tion.
G: CopySeqAll
This function copies all sequence data and settings from
another timbre to the currently selected timbre.
Source Program.........................................[A01...H16]
Select the copy source program.
Source Timbre......................................................[1, 2]
Select the copy source timbre.
Procedure
1 In LCD Edit mode, press the SELECT [16] key and then
press the CURSOR [®] key six times.
The LCD screen will show Page 26G: UTILITY “CopySe-
qAll.”
2 Press the [+/YES] key.
The LCD screen will indicate the copy source program
(Source Program) and timbre (Source Timbre).
3 Use the [+/YES] [–/NO] keys to select the copy source
program.
4 Use CURSOR [®] to move the cursor to the copy
source timbre.
5 Use the [+/YES] [–/NO] keys to select the copy source
timbre.
If you selected a Single program as the copy source, it is
not possible to select the copy source timbre (only tim-
bre 1 is available).
6 Use the CURSOR [®] key to move the cursor to “OK,”
and press the [+/YES] key.
You will be asked to confirm the copy function.
7 Press the [+/YES] key once again.
The copy will be completed, and the display will indi-
cate “Completed.”
8 Press the [EXIT] key.
You will return to the first screen of the “CopySeqAll”
function.
H: SwapSeq
This function swaps the sequences of the currently selected
timbre.
Swap Seq ..........................................................[1...3]
Select the sequence that you wish to swap.
Procedure
1 In LCD Edit mode, press the SELECT [16] key and then
press the CURSOR [®] key seven times.
The LCD screen will show Page 26H: UTILITY
“SwapSeq.”
2 Press the [+/YES] key.
The LCD screen will show the sequences that will be
swapped (SwapSeq).
3 Use the [+/YES] [–/NO] keys and the CURSOR [®] key
to specify the sequences that will be swapped.
4 Use the CURSOR [®] key to move the cursor to “OK,”
and press the [+/YES] key.
You will be asked to confirm the swap function.
5 Press the [+/YES] key once again.
The copy will be completed, and the display will indi-
cate “Completed.”
6 Press the [EXIT] key.
You will return to the first screen of the “SwapSeq” func-
tion.
26F UTILITY
Are You Sure OK?
26G UTILITY
CopySeqAll OK?
26G UTILITY
A01 T:1 OK?
Source Program Source Timbre
26G UTILITY
Are You Sure OK?
26H UTILITY
SwapSeq OK?
26H UTILITY
S:1 <> S:2 OK?
SwapSeq
26H UTILITY
Are You Sure OK?