Filter
Top Products
112
Effect/Parameter List
Appendices
Time (Reverb Time) #
Adjust the time length of reverberation.
HF Damp
Adjust the frequency above which the reverberant sound will
be cut. As the frequency is set lower, more of the high
frequencies will be cut, resulting in a softer and more muted
reverberance. If you do not want the high frequencies to be cut,
set this parameter to BYPASS.
Low Gain
Adjust the gain of the low frequency range.
Positive (+) settings will emphasize (boost) the low frequency
range.
High Gain
Adjust the gain of the high frequency range.
Positive (+) settings will emphasize (boost) the high frequency
range.
Balance (Effect Balance) #
Adjust the volume balance between the direct sound and the
reverb sound. With a setting of D100:0W only the direct sound
will be output, and with a setting of D0:100W only the reverb
sound will be output.
Level (Output Level)
Adjust the output level.
25: GATED REVERB
Gate Reverb is a special type of reverb in which the reverberant
sound is cut off before its natural length.
Type (Gated Reverb Type)
Select the type of reverb.
NORMAL
: conventional gate reverb
REVERSE
: backwards reverb
SWEEP1
: the reverberant sound moves from right to left
SWEEP2
: the reverberant sound moves from left to right
Pre Delay (Pre Delay Time)
Adjust the time delay from when the direct sound begins until
the reverb sound is heard.
Gate Time
Adjust the time from when the reverb is heard until when it
disappears.
Low Gain
Adjust the gain of the low frequency range.
Positive (+) settings will emphasize (boost) the low frequency
range.
High Gain
Adjust the gain of the high frequency range.
Positive (+) settings will emphasize (boost) the high frequency
range.
Balance (Effect Balance) #
Adjust the volume balance between the direct sound and the
reverb sound. With a setting of D100:0W only the direct sound
will be output, and with a setting of D0:100W only the reverb
sound will be output.
Level (Output Level) #
Adjust the output level.
26: OD
→
CHORUS (Overdrive
→
Chorus)
This effect connects an overdrive and a chorus in series.
OD Drive
Adjust the degree of overdrive distortion. The volume will
change together with the degree of distortion.
OD Pan (Overdrive Pan) #
Adjust the stereo location of the overdrive sound. L64 is far left,
0 is center, and 63R is far right.
Cho Delay (Chorus Pre Delay Time)
Adjust the time delay from when the direct sound begins until
the chorus sound is heard.
Cho Rate (Chorus Rate)
Adjust the modulation speed of the chorus effect.
Cho Depth (Chorus Depth)
Adjust the modulation depth of the chorus effect.
Cho Bal (Chorus Balance) #
Adjust the volume balance between the overdrive sound that is
sent through the chorus and the overdrive sound that is not sent
through the chorus. With a setting of “D100:0W,” only the
overdrive sound will be output. With a setting of “D0:100W,”
only the overdrive sound that is sent through the chorus will be
output.
Level (Output Level)
Adjust the output level.
27: OD
→
FLANGER (Overdrive
→
Flanger)
This effect connects an overdrive and a flanger in series.
OD Drive
Adjust the degree of overdrive distortion. The volume will
change together with the degree of distortion.
OD Pan (Overdrive Pan) #
Adjust the stereo location of the overdrive sound. L64 is far left,
0 is center, and 63R is far right.
Flg Delay (Flanger Pre Delay Time)
Adjust the time delay from when the direct sound begins until
the flanger sound is heard.
Flg Rate (Flanger Rate)
Adjust the modulation speed of the flanger effect.
Flg Depth (Flanger Depth)
Adjust the modulation depth of the flanger effect.
Flg Fbk (Flanger Feedback Level)
Adjust the proportion (%) of the flanger sound that is fed back
into the effect. Negative (-) settings will invert the phase.
RD-700_e.book 112 ページ ２００４年４月２６日 月曜日 午前１１時５４分