Filter
Top Products
12
VR800 Owner’s Manual (Names and Functions)
26. Hold/> key [HOLD/>]
Pressing the HOLD/> key while the recorder is operating
will cause the VR800 to capture the time when you pressed
it (or bar/beat/clock value), display it, and then enter edit
mode. (If you press the HOLD/> key while the recorder
section is stopped, the VR800 enter edit mode directly.)
To cancel edit mode, press the STOP button, DISP SEL key,
or the EXIT/NO key.
“CLIPBOARD PLAY” operation starts. (See
below.) . During the operation, the STOP
lamp flashes and the PLAY lamp lights up.
ABS 0 is located. (See below.)
REC END is located. (See below.)
* CLIPBOARD PLAY operation
The CLIPBOARD PLAY operation plays back data on the clipboard. (If the
clipboard does not contain any data, the display shows [Void Data !] and
nothing happens.). During this operation, the display indicates the type of
the data (“Copy Clip” for copy data, and “Move Clip” for move data), and the
duration. The indicator of the copy source or move source track will flash.
This way, you will know which track the currently playing data comes from
and why the data is on the clipboard.
* ABS 0 locate operation
This operation locates the beginning of the current program (ABS time:
00m 00s 00f).
* REC END locate operation
This operation locates the end of the audio recording (REC END) on the
real track in the current program.
* Refer to page 36 for more information on AUTO PUNCH
mode.
* Refer to page 24 for more information on input monitoring
and playback monitoring.
24. Record button [RECORD/ AUTO PUNCH ]
Pressing the PLAY button while holding down this button
will start the VR800 recording any READY tracks.
The flashing lamp of the RECORD TRACK select key for the
corresponding READY track will light steadily, and the PLAY
lamp and the RECORD lamp light.
If you press only the RECORD button, a READY real track
enters input monitoring mode (The RECORD lamp flashes.).
At this time, pressing the RECORD button again will cancel
the input monitoring mode, and the track will return to the
playback monitoring mode.
Pressing the RECORD button while holding down the SHIFT
key will toggle between AUTO PUNCH on and off.
* Refer to page 54 for more information on these operations.
* Refer to page 40 for more information on the Punch In/
Out operation using a foot switch.
STOP
PLAY
REW
F FWD
Press the STORE key, and press the CLIPBOARD IN key.
The CLIPBOARD IN point will be stored.
This data can be used as locate data.
Press the STORE key, and press the CLIPBOARD OUT key.
The CLIPBOARD OUT point will be stored.
This data can be used as locate data.
Press the STORE key, and press the AUTO PUNCH IN key.
The AUTO PUNCH IN point will be stored.
This data can be used as locate data.
Press the STORE key, and press the AUTO PUNCH OUT key.
The AUTO PUNCH OUT point will be stored.
This data can be used as locate data.
Press the STORE key, and press the AUTO RTN START key.
The AUTO RTN START point will be stored.
This data can be used as locate data.
Press the STORE key, and press the AUTO RTN END key.
The AUTO RTN END point will be stored.
This data can be used as locate data.
25. Store key [STORE]
This is the key for registering (storing) the time (or BAR/
BEAT/CLK figures) for ABS or MTC into any memory key or
LOCATE key. The key lamp will be lit when this is pressed
and together with a display of [Press LOC:], the locate
number will blink. When registering time data in a memory
key such as AUTO PUNCH IN, any memory key can be
pressed by ignoring this [Press LOC:] display, when
registering in the LOCATE key, specify any locate number
(01~99) while [Press LOC:] is displayed, then press the
LOCATE key. In either case, the STORE key lamp will be
extinguished simultaneous with the completion of time data
registering, and return to the original time base display.
After pressing this key, if you wish to cancel the store
operation, press the EXIT/NO key, or STOP button.
* Refer to page 54 for more information on the Locate function.
* Refer to page 48 for more information on storing edit points
(locate points).
* Refer to page 32 for more information on the Program Select
function.
If you press the STORE key and the HOLD/> key
simultaneously while the recorder is stopped, the VR800
will enter the program select mode, in which you can select
a program or set up a new one.
Specify locate number and press LOCATE key
The specified locate number will be stored as locate data.
A maximum 99 locate numbers can be registered.