Filter
Top Products
83
VR800 Owner’s Manual (Saving and Loading Song Data)
Flashing
Saving data
1. Press the SETUP key to enter SETUP mode.
2. Use the JOG dial to select [Save PGM ?] menu, then
press the EXECUTE/YES key.
[Device ?] appears and the selected output signal option
flashes. ([SCSi id-6] flashes.)
<[Save PGM ?] menu>
* Output signal options: [AdAt], [dAT], [SCSi id-6]
* Program options: P01 - P99 (an individual Program)
* Track options: When using an adat or DAT: tracks 1–8,
tracks 1–16, Tracks 1–24;
When using a SCSI disk (SCSi id-6): All tracks
will be automatically selected.
* You can back up data using the “Save PGM ?” menu in
SETUP mode.
The following procedure assumes that Program 1 on
the 3.5-inch E-IDE hard disk (current drive) contains
performance data.
Flashing
3. Use the JOG dial to select the desired digital signal
for the save operation ([dAT] or [AdAt]).
4. Press the EXECUTE/YES key.
The number of the Program selected before the VR800
entered SETUP mode flashes on the display, indicating
that you can select a Program to save.
Select this to save data in the adat digital signal
format to a connected adat.
Select this to save data in the S/P DIF digital signal
format to a connected DAT.
[AdAt]
[dAT]
Flashing
Flashing
5. Use the JOG dial to select a Program to save.
If multiple Programs exists in the current drive disk, turn
the JOG dial to change the Program number.
Flashing
To edit the time value, use the HOLD/> key, REWIND
button, or F FWD button to move the flashing cursor to
the desired digit, and turn the JOG dial to change the
value. (The above example shows you can edit the minute
value.)
7. Press the EXECUTE/YES key.
The VR800 displays the track selection screen.
First, Real tracks 1–8 appear. Turn the JOG dial to change
number “8” to the desired number.
Flashing
8. Use the JOG dial to select the desired tracks.
Options are Tr 1–8, Tr 1–16 (Real track 1–8 and
Additional track 9–16), or Tr 1–24 (Real track 1–8 and
Additional track 9–24).
9. Press the EXECUTE/YES key.
The display changes as follows.
This means “Start recording on the DAT (or adat)!”
10. Start recording on the DAT (or adat).
At this time you could set a START-ID or a locate point at
the recording start point so that you will be able to find
the top of the Program to load later.
11. Press the EXECUTE/YES key.
The VR800 starts saving data and displays the total time
required for the save operation. The time value starts
counting down a few seconds later.
CLK
SYNC OUT DRIVE
IDE
AUTO A.PUNCH
SETUP
44.1kHz
DIGITAL
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
IDE
44.1kHz
DIGITAL
CLK
SYNC OUT DRIVE
IDE
AUTO A.PUNCH
SETUP
44.1kHz
PGM
DIGITAL
6. Press the EXECUTE/YES key.
CLK
SYNC OUT DRIVE
IDE
AUTO A.PUNCH
SM
PGM
DIGITAL
CLK
SYNC OUT DRIVE
IDE
AUTO A.PUNCH
SETUP
44.1kHz
DIGITAL
CLK
SYNC OUT DRIVE
IDE
AUTO A.PUNCH
SETUP
?
SURE
44.1kHz
DIGITAL
The total time saved in the selected program will be shown
in the display, and this time can then be edited.
Normally, the displayed time is saved as it is. But, as men-
tioned in <Notes when saving data using DAT or adat> on
page 77, in cases where the data on the additional track is
longer than that on the real track, the time to ve saved can
be edited. However, time which can be edited has to be a
maximum 59 minutes 59 seconds. This feature is also effec-
tive for making a short save.