Filter
Top Products
9
VR800 Owner’s Manual (Names and Functions)
4.Contrast adjustment knob
Use this knob to adjust the contrast of the LCD. Turning
this knob clockwise will increase the contrast, and turning
it counter-clockwise will decrease the contrast.
Note:
The display is not unreadable if you leave the knob
counter-clockwise all the way.
5.Clipboard In key [CLIPBOARD IN/ PREVIEW ]
Use this key to store the start point of audio data to be
copied or moved. When you press this key, the VR800
displays data currently stored, and you can edit the data.
After editing the data, press the STORE key, then press the
CLIPBOARD IN key to store the edited data in this key. The
stored data can be used as locate data.
If you press the CLIPBOARD IN key while holding down the
SHIFT key when the recorder is stopped, you can preview
the fade-in part at the stored CLIPBOARD IN point.
* Refer to page 51 for more information on setting and editing
the locate point.
* Refer to page 61 for more information on the Copy & Paste/
Move & Paste functions.
* Refer to page 59 for more information on previewing data
at the CLIPBOARD IN point
6.Clipboard Out key [CLIPBOARD OUT/ PREVIEW ]
Use this key to store the end point of audio data to be copied
or moved. When you press this key, the VR800 displays
currently-stored data, which you can edit. After editing the
data, press the STORE key, then press the CLIPBOARD OUT
key to store the edited data in this key. The stored data can
be used as locate data.
If you press the CLIPBOARD OUT key while holding down
the SHIFT key when the recorder is stopped, you can preview
the fade-out part at the stored CLIPBOARD OUT point.
* Refer to page 51 for more information on setting and editing
the locate point.
* Refer to page 61 for more information on the Copy & Paste/
Move & Paste functions.
* Refer to page 59 for more information on previewing data
at the CLIPBOARD OUT point
7. Exit/No key [EXIT/NO/ EJECT ]
This key is the counterpart of the EXECUTE/YES key.
Press this key to cancel an operation.
When you use a removable SCSI disk, pressing this key while
holding down the SHIFT key will eject the disk.
8. Execute/Yes key [EXECUTE/YES]
Press this key to confirm the edit operations, such as Copy
& Paste, Move & Paste, and Erase, and to set the parameters
of SETUP menus.
Currently-selected Time Base indication *1
Currently-selected Time Base REMAIN indication *2
External MTC IN indication *3
*1 The current position in terms of time base selected via the TIME
BASE SEL key appears. ABS time, MTC time, or BAR/BEAT/CLK is
used.
*2 Available recording time and space on the current SCSI disk will
appear. The time indication uses the currently-selected time base
(ABS, MTC, or BAR/BEAT/CLK). The space indication uses MB
(Megabyte). (The values are based on mono track recording.)
*3 MTC being input from an external MIDI device to the VR800 appears.
If no MTC is input, the display will show “00H 00M 00S 00F.”
9.Display indication select key [DISP SEL]
Pressing this key each time will change the display indication
as follows:
Refer to page 88 for more information on SETUP mode.
10. Setup key [SETUP]
Press this key to set the VR800 in SETUP mode to execute
various menus. This key works only when the VR800 is
stopped.
11. Undo/Redo key [UNDO/REDO]
If you wish to restore the status prior to editing, recording,
or performing a punch in/out take, press the UNDO/REDO
key. Pressing the UNDO/REDO key again will restore the
status obtained before you pressed the UNDO/REDO key
the first time.
When you undo the operation, [Undo!] will appear. When
you redo the operation, [Redo!] will appears on the display.
Note:
The Undo/Redo function works only when the VR800
is stopped.
Refer to pages 39, 42, 63, 65 and “Quick operation guide” for
more information on the Undo/Redo function.