Filter
Top Products
99
VR800 Owner’s Manual (Changing the initial setting: SETUP mode)
3. Use the JOG dial to turn Slave mode on and off.
Rotating the JOG dial clockwise and counter-clockwise
alternates flashing [on] and [oFF].
Selecting [on] turns Slave mode on, and selecting [oFF]
turns Slave mode off.
4. Press the EXECUTE/YES key.
If you select [oFF], [e] and [?] flash alternately.
If you select [on], [e] and [?] flash alternately and [SLAVE]
flashes as shown below.
This means that the VR800 has not locked to the sync
signal. When the VR800 locks to the sync signal from the
master device, [SLAVE] lights up steadily.
After you set Slave mode to [on], you need to select the
Slave type (type of sync signal) described in the next section.
To cancel the operation, or to restore the setting obtained
prior to the EXECUTE/YES key press, press the STOP
button or the EXIT/NO key. Each time you press one of
these keys, the VR800 returns to the previous hierarchy
level of the menu, and finally exits SETUP mode and
displays the previous Time Base.
1. While the VR800 is stopped, press the SETUP key
to enter SETUP mode.
2. Turn the JOG dial to select [Slave Type (?)] ([e] and [?]
flash alternately), then press the EXECUTE/YES key.
The current Slave type appears on the display.
Pressing the EXECUTE/YES key turns off the flashing [?]
character, and the Slave type indicator flashes.
With the initial setting, [VA ri] flashes as shown below.
3. Use the JOG dial to select the desired Slave type.
Rotating the JOG dial clockwise and counter-clockwise
will cause the [VA ri] and [Fr EE] indicators to flash in
sequence.
<Notes>
• You need to input MTC from an external device to the VR800 with
any Slave type.
• The VR800 re-chase window is fixed to ten frames. That is, if an
offset between the master device and slave device exceeds ten
frames, the VR800 interprets that as out of sync, and tries to chase
and lock to MTC sent from the master device. (This operation is
called “re-chasing.”) During the re-chase operation, audio output
is muted. If the slave machine slips with MTC from the master
device by less than ten frames, the slave machine continues
running while recognizing the slippage.
• When you set the Slave type, the Vari Pitch function is automatically
disabled. (The [VARI PITCH] indicator turns off.)
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
SLAVE
44.1kHz
DIGITAL
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
44.1kHz
DIGITAL
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
44.1kHz
DIGITAL
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
44.1kHz
DIGITAL
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
44.1kHz
DIGITAL
Setting the Slave type (“Slave Type ?” menu)
The “Setting the Slave type” menu enables you to setup how VR800 should function after chase lock, when
VR800 is set to sync externally in “slave mode ON” by the previously mentioned “Setting the slave mode.”
Setting the Slave type
• Initial setting : [VAri]
• Option : [VA ri], [Fr EE]
[VA ri]: The VR800 synchronizes only to external MTC.
[Fr EE]: The VR800 locks to MTC, then synchronizes to the internal clock.
* You can set the parameter for each Program individually.
* The settings can be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the unit.
* The Program is automatically checked before the operation.
* The sampling rate is automatically checked before the operation.
lights up
flashes
flashes