Filter
Top Products
Part III Sequencer
69
QQTG0701
Sequencer
Chord data
When the chord name is displayed at the cursor
position, you can press the DELETE key to
erase the data and then store a new chord.
• If you do not erase the displayed data before entering new
chord data, the new data is inserted at this point, and the
displayed data is merely shifted by the note value of the
new chord.
• Rests can also be erased. Each time the DELETE key is
pressed, the rest is erased in units of
Œ
× 1. The
‰
rest is
erased last.
• If you wish to cancel the REPEAT, enter an END com-
mand.
Control data
The name of the stored function (INTRO, FILL,
etc.) is displayed. You can press the DELETE
key to erase the data which is displayed.
Ⅲ
ⅢⅢ
Ⅲ
TRACK CLEAR
To erase all data from the current track, press
the CLR button, and then press the YES button
on the confirmation display.
• If you wish to cancel the clear procedure, press the NO
button.
Store a rhythm progression
Changes in the rhythm selection and tempo, as well as the intro, fill-ins and the ending, can be stored by
measures with the step recording method.
1.
On the SEQ MENU display, use the SONG
∧
and
∨
buttons to select the song number.
Then select RECORD & EDIT.
2.
On the RECORD & EDIT display, select STEP
RECORD.
• The display changes to the PART SELECT display.
3.
Using the balance buttons below the display,
select the track to which the RHYTHM (RHY)
part has been assigned.
• The display changes to the STEP RECORD: RHYTHM
input display similar to the following.
4.
Use the MEAS ▲ and ▼ buttons to go to the
measure you wish to record.
5.
Store the rhythm data.
• Data which can be stored:
START/STOP
Changes in the rhythm selection
RHYTHM VARIATION 1–4,
COUNT INTRO, INTRO, FILL IN,
ENDING
Tempo changes
• Be sure to store the START/STOP data in the measure in
which the rhythm starts or stops.
• If you are storing a COUNT INTRO or INTRO, store this
data before the START/STOP data.
• If the tempo is changed, the display changes to the con-
firmation display. After specifying the desired tempo,
Press the YES button to store the specified tempo, or
press the NO button to cancel the new tempo value.
6.
Repeat steps 4 and 5 to continue storing the
rhythm progression.
7.
At the end of the rhythm progression, press
the END button.
• If the REP button is pressed instead of the END button,
during playback the recorded rhythm progression is
repeated.
• The Keyboard exits the recording mode.
Ⅲ
ⅢⅢ
Ⅲ
Correct the recorded rhythm progression
1.
Follow the procedure to select the STEP
RECORD: RHYTHM display.
2.
Use the MEAS buttons to go to the measure
you wish to modify. (The
∗
is highlighted.)
3.
Correct the rhythm data.
• Press the ERS button to erase data at the cursor posi-
tion.
• If you wish to cancel the REPEAT, enter an END com-
mand.
• If you select a rhythm with a different time signature, the
time signature of all subsequent measures will also
change.
• If data has already been recorded in other tracks, you
cannot select a rhythm with a different time signature.
Ⅲ
ⅢⅢ
Ⅲ
TRACK CLEAR
To erase all data from the current track, press
the CLR button, and then press the YES button
on the confirmation display.
• If you wish to cancel the clear procedure, press the NO
button.
08_Part III.fm 69 ページ ２００３年５月１６日 金曜日 午後５時４１分