Fostex FD-8 Musical Instrument User Manual


 
108
Changing the initial setting (SETUP mode)
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
44.1kHz
4. Press the EXECUTE/YES key.
The selected Slave type is stored, and [e] and [?] flash
alternately.
Setting the Record Protect function (“Rec Protect ?” menu)
The FD-8 features the Record Protect function, which is similar to the function of record-protect tabs on cassette
tapes. The “Setting the Record Protect function” menu allows you to turn the Record Protect function on and off.
When this function is turned on, you cannot record, paste, or erase data. Use this function to protect your
precious data from being erased accidentally.
• Initial setting: [o FF]
• Option: [on] or [o FF]
* You can turn the function on and off for each Program individually.
* The settings can be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the unit.
* The Program is automatically checked before the operation.
<Notes>
• This menu is used to select a digital signal used for external
synchronization when Slave mode is turned on. If you wish to specify
the type of digital signals to record, you need to use the “Setting
digital input tracks” menu.
• When you set the Slave type, the Vari Pitch function is
automatically disabled. (The [VARI PITCH] indicator turns off.)
<Notes>
• If you set the Slave type to [SP di F] (S/P DIF digital signal) or [Ad
At] (adat digital signal), [DIGITAL] lights up on the display when the
FD-8 receives a normal digital signal from the external device. If
the signal is abnormal, the [DIGITAL] indicators flash to give you an
alarm.
• If you set the Slave type to [SP diF] (S/P DIF digital signal),
approximately two seconds of the sound in the entire system will be
muted when the FD-8 locks or unlocks to clock. Make sure to input
a stable digital signal source.
To cancel the operation, or to restore the setting obtained
prior to the EXECUTE/YES key press, press the STOP
button or the EXIT/NO key. Each time you press one of
these keys, the FD-8 returns to the previous hierarchy
level of the menu, and finally exits SETUP mode and
displays the previous Time Base.
Recording enabled/disabled
1. While the FD-8 is stopped, press the SETUP key to
enter SETUP mode.
2. Turn the JOG dial to select [Rec Protct (?)] ([t] and
[?] flash alternately), then press the EXECUTE/YES
key.
The current setting appears on the display.
Pressing the EXECUTE/YES key turns off the flashing [?]
character, and the recording enabled/disabled indicator
flashes.
With the initial setting, [o FF] flashes as shown below.
3. Use the JOG dial to enable or disable recording.
Rotating the JOG dial clockwise and counter-clockwise
will flash [on] and [o FF] alternately.
Selecting [o FF] enables recording; you can record, paste,
and erase data.
Selecting [on] disables recording; and you cannot record,
paste, or erase data.
4. Press the EXECUTE/YES key.
[t] and [?] flash alternately.
Note:
When recording is disabled (on) and you try to record,
paste, or erase data, the FD-8 displays [Protected] for a second,
indicating that you cannot perform the operation. To perform
the operation, you need to enable recording (oFF).
To cancel the operation, or to restore the setting
obtained prior to the EXECUTE/YES key press, press
the STOP button or the EXIT/NO key. Each time you
press one of these keys, the FD-8 returns to the
previous hierarchy level of the menu, and finally exits
SETUP mode and displays the previous Time Base.
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
44.1kHz