Filter
Top Products
92
Saving and Loading Song Data
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
44.1kHz
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
SETUP
44.1kHz
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
SETUP
44.1kHz
PGM
Flashing
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
SETUP
44.1kHz
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
SETUP
?
SURE
44.1kHz
Saving data
1. Press the SETUP key to enter SETUP mode.
2. Use the JOG dial to select [Save PGM ?] menu, then
press the EXECUTE/YES key.
[Save Device ?] appears and the selected output signal
option flashes ([dAT], [AdAt], or [SCSi id-6].)
<[Save PGM ?] menu>
* Output signal options: [AdAt], [dAT], [SCSi id-6]
* Program options: P01 - P99 (an individual Program)
* Track options: When using an adat or DAT: tracks 1–8,
tracks 1–16, Tracks 1–24;
When using a SCSI disk (SCSi id-6): All tracks
will be automatically selected.
* You can back up data using the “Save PGM ?” menu
in SETUP mode.
The following procedure assumes that Program 1 on
the 2.5-inch IDE internal hard disk (current drive)
contains performance data.
Flashing
3. Use the JOG dial to select the desired digital signal
for the save operation ([dAT] or [AdAt]).
4. Press the EXECUTE/YES key.
The number of the Program selected before the FD-8
entered SETUP mode flashes on the display, indicating
that you can select a Program to save.
Select this to save data in the adat digital signal
format to a connected adat.
Select this to save data in the S/P DIF digital signal
format to a connected DAT.
[AdAt]
[dAT]
Flashing
Flashing
5. Use the JOG dial to select a Program to save.
If multiple Programs exists in the current drive disk, turn
the JOG dial to change the Program number.
6. Press the EXECUTE/YES key.
The FD-8 displays the total time of the selected Program.
You can edit this total time value. That is, you can shorten
the time required for the save operation.
For example, if the duration of the Program is 8 minutes
25 seconds, you can edit this time value to 5 minutes.
(You can edit up to 59 minutes 59 seconds.)
This is useful when the backup tape lacks adequate space.
Flashing
To edit the time value, use the HOLD/> key, REWIND
button, or F FWD button to move the flashing cursor to
the desired digit, and turn the JOG dial to change the
value. (The above example shows you can edit the minute
value.)
7. Press the EXECUTE/YES key.
The FD-8 displays the track selection screen.
First, Real tracks 1–8 appear. Turn the JOG dial to change
number “8” to the desired number.
Flashing
8. Use the JOG dial to select the desired tracks.
Options are Tr 1–8, Tr 1–16 (Real track 1–8 and
Additional track 9–16), or Tr 1–24 (Real track 1–8 and
Additional track 9–24).
9. Press the EXECUTE/YES key.
The display changes as follows.
This means “Start recording on the DAT (or adat)!”
10. Start recording on the DAT (or adat).
At this time you could set a START-ID or a locate point at
the recording start point so that you will be able to find
the top of the Program to load later.
11. Press the EXECUTE/YES key.
The FD-8 starts saving data and displays the total time
required for the save operation. The time value starts
counting down a few seconds later.
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
SM
PGM