Filter
Top Products
13
Names and Functions
Press the STORE key, and press the CLIPBOARD IN key.
The CLIPBOARD IN point is stored.
This data can be used as locate data.
Press the STORE key, and press the CLIPBOARD OUT key.
The CLIPBOARD OUT point is stored.
This data can be used as locate data.
Press the STORE key, and press the AUTO PUNCH IN key.
The AUTO PUNCH IN point is stored.
This data can be used as locate data.
Press the STORE key, and press the AUTO PUNCH OUT key.
The AUTO PUNCH OUT point is stored.
This data can be used as locate data.
Press the STORE key, and press the AUTO RTN START key.
The AUTO RTN START point is stored.
This data can be used as locate data.
Press the STORE key, and press the AUTO RTN END key.
The AUTO RTN END point is stored.
This data can be used as locate data.
Copy Clip
Move Clip
Copy Paste (or Move Paste *)
Erase
TRK Exchange
34. Store key [STORE]
This key is used to store time values (or bar/beat/clock
values) in the memory keys. Press this key, then one of the
following keys to store data indicated on the display
(including edit data) in the corresponding memory key. If
you press the STORE key and the HOLD/> key
simultaneously while the recorder is stopped, the FD-8 enters
Program Select mode, in which you can select a Program or
set up a new Program.
To cancel the store operation after you have pressed this
key, press the EXIT/NO key.
* Refer to page 70 for more information on the Locate function.
* Refer to page 66 for more information on storing edit points
(locate points).
* Refer to page 33 for more information on the Program Select
function.
35. Undo/Redo key [UNDO/REDO]
If you wish to restore the status prior to editing, recording,
or performing a punch in/out take, press the UNDO/REDO
key. Pressing the UNDO/REDO key again will restore the
status obtained before you pressed the [UNDO/REDO] key
the first time.
When you undo the operation, [Undo!] appears. When you
redo the operation, [Redo!] appears on the display for a
short moment.
Note:
The Undo/Redo function is enabled only when the
FD-8 is stopped.
Refer to pages 44, 47, 58, 60 and “Quick operation guide” for
more information on the Undo/Redo function.
36. Edit key [EDIT]
Pressing this key causes the FD-8 to enter menu selection
mode for editing tracks, and displays the title of the menu
you used last time. Press this key repeatedly or turn the
JOG dial to select a menu. The edit menus appear in the
following order. To execute a desired menu, select the menu,
then press the EXECUTE/YES key.
To exit selection mode, press the EXIT/NO key.
(*) After you execute Copy Clip, “Copy Paste” appears. After you execute
Move Clip, “Move Paste” appears.
* Refer to page 56 for more information on Copy & Paste and
Move & Paste.
* Refer to page 59 for more information on Erase.
* Refer to page 61 for more information on Track Exchange.
37. Auto Return Start key
[AUTO RTN START/ PREVIEW ]
Use this key to store the start point (AUTO RTN START point)
for the Auto Return function and the Auto Repeat function.
When you press this key, the FD-8 displays the currently-
stored data, which you can edit. After editing the data, press
the STORE key, then the AUTO RTN START/PREVIEW key
to store the edited data in this key. The stored data can be
used as locate data.
This memory is reset to the factory default value when you
turn off the power to the FD-8.
If you press the AUTO RTN START/PREVIEW key while
holding down the SHIFT key when the recorder is stopped,
you can preview the fade-in part at the stored AUTO RTN
START point.
* Refer to page 66 for more information on setting and editing
the AUTO RTN START point.
* Refer to page 70 for more information on the Auto Return
and Auto Repeat functions.
* Refer to page 74 for more information on previewing data
at the AUTO RTN START point.