Filter
Top Products
88
Saving and Loading Song Data
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
44.1kHz
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
SETUP
44.1kHz
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
SETUP
?
SURE
44.1kHz
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
REMAIN
SETUP
MB
44.1kHz
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
ABS
44.1kHz
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
REMAIN
SETUP
MB
44.1kHz
SETUP
DRIVE
AUTO A.PUNCH
SYNC OUT
CLK
SCSI
44.1kHz
COMPLETED !
Saving data
<[Save PGM ?] menu>
* Output signal options: [AdAt], [dAT], [SCSi id-6]
* Program options: P01 - P99 (an individual Program)
* Track options: When using an adat or DAT: tracks 1–8,
tracks 1–16, Tracks 1–24;
When using a SCSI disk: All tracks will be
automatically selected.
1. Insert an unformatted disk into the backup drive.
2. Press the SETUP key to enter SETUP mode, then
use the JOG dial to select [Save PGM ?] menu.
3. Press the EXECUTE/YES key.
[Save Device ?] appears and the selected output signal
option flashes. ([dAT] flashes.)
4. Turn the JOG dial to select a flashing [SCSi id-6] to
select the connected SCSI drive as a save
destination.
5. Press the EXECUTE/YES key.
The FD-8 recognizes that a disk in the backup drive is
unformatted, and displays [Unformat ?], then proceeds
to the [Bk Format?] menu (backup disk format) in SETUP
mode, then displays the following.
6. Press and hold down the RECORD button, and
press the EXECUTE/YES key.
The FD-8 displays the following and starts formatting the
disk. The unformatted disk area size will count down as
the format operation progresses.
When the formatting operation is completed,
[COMPLETED !] lights up, [SCSi id-6] flashes, then the FD-
8 displays the following.
This example shows that the data to be saved is Program
1 on the current drive. If the current drive has multiple
Programs, use the JOG dial to select the desired Program.
7. Use the JOG dial to select the desired Program and
press the EXECUTE/YES key.
The save operation starts and the following indication
appears.
This example shows that Program 1 data is being saved
as Backup data 1. As the save operation progresses, the
REMAIN value (e.g.: -58MB) counts down.
When the save operation is completed, [COMPLETED!]
lights up and the following indication appears.
8. Press the EXIT/NO key to exit SETUP mode.
The FD-8 displays ABS 0 of the Program on the current
drive.
The above procedure assumes that the saved data size is
smaller than the available space of the backup disk. You can
use only one backup disk. To save data larger than a single
backup disk, refer to the next <Memo> for information on
saving data using multiple backup disks.
Note:
The backup data will use the number of the saved
Program. (e.g., if you save P01 [#0001 data, the backup data
will be named as B01[#0001.) You cannot edit the title of the
backup data.
CLK
SYNC OUT DRIVE
SCSI
AUTO A.PUNCH
SETUP
44.1kHz
* You can back up data using the “Save PGM ?” menu
in SETUP mode. The following procedure assumes that
a recorded disk has been inserted in the current SCSI
drive, Program 1 (P01) has been selected, and an
unformatted disk will be used as the backup disk.
Flashing
Flashing
Flashing
Lights up
Flashing