Filter
Top Products
121
Appendices
Troubleshooting
Appendices
Troubleshooting
If you experience problems, refer to the relevant item
and take the appropriate measures.
Power does not turn on
• Is the AC/AC power supply connected to an
outlet?....................................................................
☞p.12
• Is the [POWER] switch turned on?
Turn on the rear panel [POWER] switch.
The power is turned on, but nothing is shown in
the LCD screen.
The TR functions normally when you play the key-
board or perform other operations.
• Due to changes in the surrounding temperature, the
LCD screen may on rare occasions be difficult or
impossible to read. If this occurs, perform the
following procedure. (
☞PG p.127)
1 Press the [EXIT] key three times, and press the
[GLOBAL] key.
2 Hold down the [EXIT] key, and press the [REC/
WRITE] key.
3 Rotate the [VALUE] dial to adjust the LCD
screen.
The power is turned on, but the LCD screen does
not display normally, or an error message is dis-
played. There is no sound when you play the key-
board, and the TR does not function normally.
• This type of problem may occur if a data writing
operation to internal memory was not completed
correctly, for example if the power of the TR was
turned off while a program or other data was being
written. If this occurs, use the following procedure
to initialize the TR’s internal memory.
1 Turn off the power.
2 Hold down the [MENU] key and the [9] key, and
turn on the power.
The TR will be initialized, and data will be written
into internal memory. While the data is being writ-
ten, the LCD screen will indicate “Now writing into
internal memory.”
No sound
• Are connections made correctly to your amp,
mixer, or headphones?........................................
☞p.12
• Is your amp or mixer turned on?
• Is Local Control turned on?
In GLOBAL 2.1: MIDI, check the “Local Control
On” check box..............................................
☞PG p.130
• Is the [VOLUME] slider raised? ..........................
☞p.5
• If there is no sound from the OUTPUT
(INDIVIDUAL) 1, 2 jacks, make sure that “BUS
Select (IFX/Indiv.Out Assign)” or “Bus Select”
following the insert effect is set to 1, 2, 1/2....
☞p.112
• If specific tracks in Sequencer mode do not
sound, Make sure that the “PLAY/MUTE/REC”
or “PLAY/MUTE” is set to PLAY....................
☞p.69
• Make sure that the “Status” is INT or BTH.....
☞p.70
• Are the “Key Zone” and “Velocity Zone” set so that
sound will be produced when you play?
..........................................................................
☞PG p.65
Notes do not stop
• In PROG 2.1: Ed–Basic, select the Prog Basic
page, make sure that the “Hold” check box is
unchecked. .......................................................
☞PG p.5
• In GLOBAL 1.1: System, Foot page, make sure that
“Damper Polarity” or “Foot SW Polarity” is set
correctly.
........................................................................
☞PG p.128
Noise or oscillation is heard
• When using the BPM/MIDI Sync function to
control the delay time of an effect, noise may occur
in the delay sound. This noise is due to
discontinuities in the delay sound, and is not a
malfunction.
• When using an effect on the external audio source
being input from AUDIO INPUT 1 and 2,
oscillation may occur depending on the type of
effect or on the parameter settings. Please adjust the
input level, output level, and effect parameters.
You need to be particularly careful when using a
high-gain effect.
• After a sample edit has been executed, or after a
stereo sample has been recorded, a small noise may
be heard. This has no effect on the audio data that
was edited or sampled.
Effects are not applied
• Are the GLOBAL 1.1: System, Basic page “IFX Off,”
“MFX1 Off,” or “MFX2 Off” settings checked?
................................................................
☞PG p.124, 125
• If you are in Combination, Sequencer, and master
effects are not applied when you raise the “S1
(Send1 (MFX1))” or “S2 (Send2 (MFX2))” of the
timbre/track, does “Return 1” or “Return 2” from
the master effect need to be raised?
....................................................................
☞PG p.47, 86
Alternatively, has “Send 1” or “Send 2” for each
oscillator of the program used by the timbre/track
been lowered?..........................................
☞PG p.45, 84