Filter
Top Products
39
Creating a Patch
Creating a Patch
BEAM-L:
D Beam controller (left)
BEAM-R:
D Beam controller (right)
KNOB1:
Assignable Controller ([C1])
KNOB2:
Assignable Controller ([C2])
VELO:
Velocity (pressure you press a key with)
KEYF:
Note Number
Sens (Matrix Control Sens)
Sets the amount of the Matrix Control’s effect that is applied. If you
wish to modify the selected parameter in a positive (+) direction –
i.e., a higher value, toward the right, or faster etc. – from its current
setting, select a positive (+) value. If you wish to modify the selected
parameter in a negative (-) direction – i.e., a lower value, toward the
left, or slower etc. – from its current setting, select a negative (-)
value. When both positive and negative are selected, the changes are
greater as the value increases. Set it to “0” if you don’t want this
effect.
Value:
-63– +63
Destination 1, 2 (Matrix Control Destination 1,
2)
Specifies the parameters that will be controlled by the matrix
controllers. When not controlling parameters with the Matrix
Control, set this to “OFF.” Up to two parameters can be specified for
each Matrix Control, and controlled simultaneously.
Value
You can control the following parameters. For details on each
parameter, refer to the corresponding reference page.
In this manual, Parameters that can be controlled using the
Matrix Control are marked with a “H.”
OSC1/2-PITCH:
Oscillator Pitch (p. 43)
OSC1/2-TIME/PW:
Time/Pulse Width (p. 44)
OSC1/2-FORMA/FAT:
Formant/Fat (p. 44, p. 45)
OSC1/2-LVL:
Level (p. 45)
OSC1/2-PENV-ATK:
Pitch Envelope Attack Time (p. 48)
OSC1/2-PENV-DCY:
Pitch Envelope Decay Time (p. 48)
OSC1/2-PENV-REL:
Pitch Envelope Release Time (p. 48)
OSC1/2-TENV-ATK:
Time Envelope Attack Time (p. 48)
OSC1/2-TENV-DCY:
Time Envelope Decay Time (p. 48)
OSC1/2-TENV-REL:
Time Envelope Release Time (p. 48)
OSC1/2-FENV-ATK:
Formant Envelope Attack Time (p. 48)
OSC1/2-FENV-DCY:
Formant Envelope Decay Time (p. 48)
OSC1/2-FENV-REL:
Formant Envelope Release Time (p. 48)
OSC1/2-AENV-ATK:
Oscillator TVA Envelope Attack Time (p. 48)
OSC1/2-AENV-DCY:
Oscillator TVA Envelope Decay Time (p. 48)
OSC1/2-AENV-REL:
Oscillator TVA Envelope Release Time (p. 48)
OSC1/2-LFO-RATE:
Oscillator LFO Rate (p. 49)
OSC1/2-LFO-PCH:
Oscillator Pitch LFO Depth (p. 43)
OSC1/2-LFO-TM/PW:
Time/Pulse Width LFO Depth (p. 44, p. 44)
OSC1/2-LFO-FR/FT:
Formant/Fat LFO Depth (p. 44, p. 45)
OSC1/2-LFO-LVL:
Oscillator Level LFO Depth (p. 45)
CSM1/2-PRM1:
(p. 111)
CSM1/2-PRM2:
(p. 111)
CSM1/2-ENV1-ATK:
COSM Envelope Attack Time (p. 48)
CSM1/2-ENV1-DCY:
COSM Envelope Decay Time (p. 48)
CSM1/2-ENV1-REL:
COSM Envelope Release Time (p. 48)
CSM1/2-ENV2-ATK:
COSM Envelope Attack Time (p. 48)
CSM1/2-ENV2-DCY:
COSM Envelope Decay Time (p. 48)
CSM1/2-ENV2-REL:
COSM Envelope Release Time (p. 48)
CSM1/2-LFO-RATE:
COSM LFO Rate (p. 49)
CSM1/2-LFO-PRM1:
(p. 111)
CSM1/2-LFO-PRM2:
(p. 111)
TVA-LVL:
Level (p. 47)
TVA-ENV-ATK:
TVA Envelope Attack Time (p. 48)
TVA-ENV-DCY:
TVA Envelope Decay Time (p. 48)
TVA-ENV-REL:
TVA Envelope Release Time (p. 48)
TVA-LFO-RATE:
TVA LFO Rate (p. 49)
TVA-LFO-LVL:
Level LFO Depth (p. 47)
TVA-LFO-PAN:
Pan LFO Depth (p. 47)
MFX-SEND:
MFX Send Level (p. 50)
CHO-SEND:
Chorus Send Level (p. 50)
REV-SEND:
Reverb Send Level (p. 50)
MFX1–3:
(p. 116)
TVA-PAN:
Pan (p. 47)
When you touch <List>, the Destination List window will
appear, allowing you to select the Matrix Control Destination
from the list.