Filter
Top Products
Owner’s Manual
Performance mode Performance Edit
82
Tone
You can set parameters related to the pitch and tone for each Part. Keep in mind that the settings made here
are applied as offsets to the Voice Edit settings.
NoteShift (NTShft)
Note Shift Determines the pitch (key transpose) setting for each Part in semitones.
Settings: -24 ~ 0 ~ +24
Detune (Detune)
Detune Determines the fine tuning for each Part.
Settings: -12.8Hz ~ +12.7Hz
Cutoff (Cutoff)
Cutoff Determines the Cutoff Frequency for each Part. If you are using LPF (Low Pass Filter) and HPF (High Pass
Filter) combined together, the parameters in the QED Filter page only affects LPF.
Settings: -64 ~ 0 ~ +63
Resonance (Reso)
Resonance Determines the amount of filter resonance. The setting here attenuates/boosts the resonance applied to the
Element of the Voice assigned to each Part.
Settings: -64 ~ 0 ~ +63
FEG Depth (FEGDpt)
FEG Depth Determines the Filter Envelope Generator depth (amount of Cutoff Frequency) for each Part.
Settings: -64 ~ 0 ~ +63
n The FEG Depth setting is not available for the Plug-in Parts.
n For details about Filter, see page 56.
FEG Attack (FEGAtk)
FEG Attack Determines each parameter of the FEG for each Part. For details about FEG, see page 70.
Settings: -64 ~ 0 ~ +63
n The FEG setting is not available for the Plug-in Parts.
n The FEG settings (except for the FEG Depth) are not available for the Drum Voice Parts.
FEG Decay (FEGDcy)
FEG Decay
FEG Sustain (FEGSus)
FEG Sustain
FEG Release (FEGRel)
FEG Release
AEG Attack (AEGAtk)
AEG Attack Determines each parameter of the AEG for each Part. Please note that Sustain Level is not available for the
Plug-in Part. For details about AEG, see page 71.
n The AEG Sustain/Release settings are not available for the Drum Voice Parts.
Settings: -64 ~ 0 ~ +63
AEG Decay (AEGDcy)
AEG Decay
AEG Sustain (AEGSus)
AEG Sustain
AEG Release (AEGRel)
AEG Release
EQ (Equalizer)
From this display you can adjust the EQ settings for each Part.
For details about the Effect connection including the EQ in the Performance mode, see page 62.
n These parameters are not available for Plug-in Voices.
L.Freq
Low Frequency Determines the center frequency of the low EQ band that is attenuated/boosted.
Settings: 50.1 ~ 2.00k
L.Gain
Low Gain Determines the amount of boost or attenuation applied to the low EQ band.
Settings: -32 ~ +32
M.Freq
Mid Frequency Determines the center frequency of the middle EQ band that is attenuated/boosted.
Settings: 139.7 ~ 10.1k
M.Gain
Mid Gain Determines the amount of boost or attenuation applied to the middle EQ band.
Settings: -32 ~ +32
M.Q
Mid Frequency Characteristic Determines the center frequency characteristic applied to the middle EQ band.
Settings: 0 ~ 31
H.Freq
High Frequency Determines the center frequency of the high EQ band that is attenuated/boosted.
Settings: 503.8 ~ 14.0k
H.Gain
High Gain Determines the amount of boost or attenuation applied to the high EQ band.
Settings: -32 ~ +32
RcvSw (Receive Switch)
From this display you can set how each individual Part responds to various MIDI data, such as Control
Change and Program Change messages. When the relevant parameter is set to “on,” the corresponding
Part responds to the appropriate MIDI data. Determines the Control Change messages corresponding to
the external controllers in the CtrlAsn display from the Performance Common Edit.
Settings: on, off (“*” indicates that the parameters are not available for the Plug-in Parts.)
CtrlChange (CC)
Control Change Indicates all the Control Change messages.
PB (PB)
Pitch Bend MIDI messages generated by using the Pitch Bend Wheel.
MW (MW)
Modulation Wheel MIDI messages generated by using the Modulation Wheel.
RB*
Ribbon Controller MIDI messages generated by using the Ribbon Controller.
ChAT (ChAT)
Channel Aftertouch MIDI messages generated by pressing and holding a note on the keyboard.
BC (BC)*
Breath Controller MIDI messages generated by using the Breath Controller.
AS1 (AS1)/AS2 (AS2)*
Assign MIDI messages generated by using the Assignable Controllers corresponding to Assign 1 and Assign 2.
FC1 (FC1)/FC2 (FC2)*
Foot Controller MIDI messages generated by using the Foot Controller.
Exp (Exp)
Expression MIDI messages (Expression) generated by using the Foot Controller.
Sustain (Sus)
Sustain MIDI messages (Sustain) generated by using the Footswitch.
n The Sustain setting is not available for the Drum Voice Parts.
FS (FS)*
Foot Switch MIDI messages generated by using the Footswitch.
UtilityVoice mode
Performance mode
Multi mode Effect Arpeggio
Reference