Filter
Top Products
Owner’s Manual
Multi mode Multi Edit
84
Multi Edit
Use Common Edit to edit the settings common to all Parts.
n Common Edit operations cannot be performed on the Multi-part Plug-in Parts 17 - 32.
These parameters are for editing the individual Parts that make up a Multi.
n You can switch the internal Parts and Plug-in Part 1 with the [1/5/9/13] button, and can switch the internal Parts and Plug-in Part 2 with [2/6/10/14] button.
Common Edit
[MULTI] (LED lights in green) → select Multi → [EDIT] → [SHIFT]+[COMMON] → select each display with PAGE
[E][F]
General
Name
Name Determines the name of the current edited Multi. The Multi name can contain up to 10 characters. For
detailed instructions on naming, see page 50.
MEQ Low/LowMid/
HighMid/High
Master EQ Offset Adjusts the master (global) EQ settings for the entire Multi. The settings made here are applied as offsets to
the EQ settings (with the exception of “MID”) from the MEQ display below.
Settings: -64 ~ +63
AssignA/B/1/2
Assign A/B/1/2 This parameter offsets the value of each Dest (Destination) parameter. Please note that certain Destinations
of Assign A/B change the absolute value.
Settings: -64 ~ +63
n Determines the Control Numbers corresponding to the Assign A and Assign B in the CtrlAsn display from the Utility
(page 90). Determines the Control Numbers corresponding to Assign 1 and Assign 2 in the CtrlAsn display in the
Multi Common Edit mode.
MEQ (Master Equalizer)
From this display you can set parameters related to the Master Equalizer (page 60). You can assign any of
five different Equalizer bands to the entire Multi. The parameters are the same as in Performance Common
Edit. See page 79.
MEF (Master Effect)
From this display you can set parameters related to the Master Effect (page 60). The parameters are the
same as in Performance Common Edit. See page 80.
CtrlAsn (Control Assign)
Determines the Control Numbers corresponding to the external controllers. The parameters are the same as
in Performance Common Edit (page 80). For details, see page 46.
Part Edit
[MULTI] (LED lights in green) → select Multi → [EDIT] → [MUTE/SEL/ENTER] (LED turns off) → select Part
with [1/5/9/13]-[4/8/12/16] → select each display
Voice
You can select a Voice for each Part.
Bank
Number
Bank
Number
Determines the Voice Bank and Voice Number for each Part. For details about Plug-in Voices, refer to the
owner’s manual of your Plug-in Board.
Mono/Poly (Mode)
Mono/Poly Selects whether each Part is played back monophonically (single notes only) or polyphonically (multiple
simultaneous notes).
Settings: mono, poly
n This parameter is not available for the Part to which the Drum Voice is assigned.
ArpSwitch (ArpSw)
Arpeggio Switch Determines whether Arpeggio is on or off for the currently selected Part.
Settings: on, off
n • Arpeggio Switch is applied to only one Part at the same time. It cannot be applied to multiple Parts simultaneously.
However, the only Parts of same receive channel can be applied simultaneously.
• The “ArpSwitch” parameter is not available for the Multi-part Plug-in Parts 17~32.
ReceiveCh (RcvCh)
Receive Channel Determines the MIDI receive channel for the selected Part. Since MIDI data may be coming from many
channels at once, you should set this to match the particular channel over which the desired controlling data
is being sent.
Settings: 01 ~ 16, off
NoteLimitL/H
(NtLmtL/H)
Note Limit Low/High Determines the note range and velocity range for each Part. The parameters are the same as in
Performance Part Edit. See page 81.
VelLimitL/H
(VlLmtL/H)
Velocity Limit Low/High Determines the Portamento parameters for each Part.
PortaSwitch (PrtSw)
Portamento Switch The parameters are the same as in Performance Part Edit. See page 81.
n • The “PortaMode” parameter setting is not available for Plug-in Voice Parts.
• These parameters are not available for the Drum Voice Parts.
PortaTime (PrtTm)
Portamento Time
PortaMode (PrtMd)
Portamento Mode
PB Upper/Lower
(PB Up/Low)
Pitch Bend Upper/Lower The parameters are the same as in Performance Part Edit. See page 81.
n For all Multi Plug-in Parts1-17 and all Plug-in Voice Parts1-2, Pitch Bend Upper and Lower become a single
parameter: PB Range. Upper and Lower values cannot be set independently for Plug-in Parts.
VelSensDpt (VelDpt)
Velocity Sensitivity Depth
VelSensOfs (VelOfs)
Velocity Sensitivity Offset
UtilityVoice mode Performance mode
Multi mode
Effect Arpeggio
Reference