Filter
Top Products
43
flashing
setting
value
curve
flashing
flashing
Adjusting EQ
The VF-16 provides a 3-band equalizer section includ-
ing HI, MID and LO bands. You can control G (gain),
F (frequency) and Q for HI and MID equalizers, while
only G (gain) for LO.
<Note>
If channels 13-14 or 15-16 are specified as the com-
pressor channels via "Setting the compressor chan-
nels" in the Setup mode, you cannot apply the
equalizer to those channels. If you press a [CH
STATUS/CH SEL] key of the compressor channel,
a warning message ("Can't Select!) flashes and the
operation is cancelled. In the screen example
shown below, the compressor is applied to chan-
nels 13-14.
1. Press the [HI-G/F/Q] (or [MID-G/F/Q] or [LO-G]) key.
The first time you bring up the channel parameter edit
screen, the message prompting to select a channel
("Select CH!") flashes, as well as all the CH STATUS/CH
SEL indicators on the panel flash.
From the second time on, the previously selected
channel is selected and ready to be edited when
bringing up the screen as shown in the drawing of step
2 below.
CH STATUS/CH SEL indicators for the compres-
sor channels do not flash.
2. Press the [CH STATUS/CH SEL] key of the desired
channel.
The current settings are shown, together with the selected
channel name. The gain value flashes, indicating that you
can edit it.
3. Use the [HI-G/F/H] (or [MID-G/F/Q] or [LO-G]) or [HOLD/
>] key to select a parameter.
Each time you press the key, the flashing parameter (to
be edited) changes in the following order.
G -> F -> Q -> ON -> G ....(When setting the LO equalizer,
the flashing parameter changes between G and ON.)
4. Use the [JOG] dial to select the desired value.
The following shows an example for editing the HI EQ's
gain. The curve corresponding to the setting value is
graphically shown. Setting this directly affects the sound.
By rotating the [JOG] dial, you can set each parameter to
the desired value within the range shown below.
•Controllable channels:
Channels 1 through 16 and the master channel.
You cannot equalize channels 13-14 or 15-16 if they
are set as the compressor channels via the Setup
mode.
•Available parameters and setting ranges:
(HI-G/F/H)
G (gain): -18 dB to FLAT to +18 dB (default:
FLAT)
F (frequency): 500 Hz to 20.2 kHz (default: 4.00
kHz)
Q: LPF, H-S, 0.1 to 20 (default: H-S)
ON/OFF: ON or OFF (default: ON)
(MID-G/F/H)
G (gain): -18 dB to FLAT to +18 dB (default:
FLAT)
F (frequency): 500 Hz to 20.2 kHz (default: 1.00
kHz)
Q: LPF, H-S, 0.1 to 20 (default: 1.0)
ON/OFF: ON or OFF (default: ON)
(LO-G)
G (gain): -18 dB to FLAT to +18 dB (default:
FLAT)
F (frequency): fixed to 400 Hz (effective
frequency: 100 Hz)
Q: fixed to L-S
ON/OFF: ON or OFF (default: ON)
*LPF: low pass filter
*H-S: hi-shelving
*L-S: low-shelving
4. To edit the EQ for another channel, repeat step 1 through
3.
5. After completing EQ editing, press the [EXIT/NO] key.
The VF-16 exits the EQ edit mode and the display returns
to the Normal display.