Filter
Top Products
73
Digital Recording
This section will describe digitally recording from the VF-16 to external digital devices or to digitally record from
external digital devices that are connected to the [DATA IN]/[DATA OUT] jack of the VF-16.
Digital signals recorded are either S/P DIF or adat digital signals.
Digital recording from an external digital device
This section describes digitally record from an external S/P DIF digital device (CD, MD, DAT, etc.) or adat digital
device (Fostex D-1624, D-824, VC-8, VM88, etc.) to the VF-16.
<Çaution (IMPORTANT)>
To digitally record to the VF-16, only input digital sig-
nals (S/P DIF or adat) with the same sampling rate
(44.1kHz/16bit) as the VF-16.
Selecting the program to record
If several programs are set, use the program selection
function to pre-start the program to record.
Setting the digital input
1. Set the VF-16 digital input as shown below, from the
"Digital In" menu in the SETUP mode.
For more details on setup procedures refer to the "SETUP
Mode" on page 107.
<When recording S/P DIF digital signals>
Set the "Digital In" (SPDIF) of the SETUP mode, as shown
as an example below. With this setting the LEFT channel
of the S/P DIF digital signal is recorded on track 1 and
the RIGHT channel is recorded on track 2.
As shown in this case, when selecting a S/P DIF digital
signal it is possible to set odd and even tracks next to each
other.
<When recording adat digital signals>
Set the "Digital In" of the SETUP mode to "adat".
This setting records the adat digital signals on ch1-ch8
on tracks 1-8. In other words, the ch1 signals are recorded
on track 1, ch2 signals on track 2, and so on. Simply put,
the digital signal is recorded on tracks corresponding to
the adat digital signal channel.
2. When the "Digital In" settings are completed, press the
[EXIT/NO] key to escape from the SETUP mode.
The LCD shows the Normal Display.
Either “ ” or “ ” lights up on the display, when
proper digital signals (S/P DIF or adat) from an external
digital device is input in DATA IN.
If either “ ” or “ ” flashes on the display it means
that the digital signal input is incorrect. In such case check
the connection cable and digital output setting of the
external device.
ACCESS
PHANTOM
CH STATUS/CH SEL
12345678
TRACK
910111213141516
TRACK
ABCDEFGH
INPUT
ORANGE
CH STATUS
INPUT RED REC GREEN PLAY MUTE
EQ/COMP
RECALL STORE
EFF1/EFF2 HI-G/F/Q
AUX1/AUX2 MID-G/F /Q
PAN LO-G
FADER CH VIEW
PRE/POST
PRE/POST
COMP
MUTE MUTE
EFF1 EFF2
DIRECT RCL MA P
SCENE
CH PARAM EDIT
EFF EDIT
OFF
CH STATUS/CH SEL
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
MASTER
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
DISP SELREC TRK
END
MARK
DIRECTBUSS
AUTO RTN
AUTO PUNCH
REC ASSIGN
REC TRKSOURCECH STATUS
AUTO PUNCH
START
SCENE SEQ.
RECORD
P.EDIT
VARI
PITCH
ALIGN SEL
SETUP
SCRUB
A RTN
A PLAY
PGM SEL
OUTOUT
LOCATE
LOC MEM
ININ
4167352
UNDO/
REDO
HOLD/ EDITSTORE
PLAYSTOP F FWDREWIND
NEXTPREV
CLIPBOARD PLAY
LOCATE ABS 0
LOCATE REC END
FADER
ADJUST
SHIFT
LEVEL
ADJUST
EXIT/NO
ENTER/YES
EJECT
JOG
SHUTTLE
2/10/B 6/14/F 7/15/G 8/16/H L R5/13/E4/12/D3/11/C1/9/A
MON OUT PHONES
UNBAL INSERTBAL UNBAL
010
PHONES
010
MON OUT
LINEMIC
PEAK
LINEMIC
PEAK
LINEMIC
PEAK
LINEMIC
PEAK
LINEMIC
PEAK
LINEMIC
PEAK
8/16/H
LINEMIC
PEAK
TRIM
INPUT
7/15/G
LINEMIC
PEAK
6/14/F5/13/E1/9/A 4/12/D3/11/C2/10/B
INSERTBAL
CLEAR
OPTICAL
DIGITAL
MULTITRACKER
TIME BASE
CLIPBOARD
DIGITAL OUT
adat digital signal or S/P DIF digital signal
DATA IN
DIGITAL/DATA OUT
75
OFFON
ANALOG INPUT MODECLOCK DIGITAL MODE
ADAT/ANALOG CONVERTER
POWER
WORD
1-41-81-2 ONSTBYINT(44.1k)OPTICAL
LOCKED
S/P DIFADAT
OPTICAL
DIGITAL OUT
<Caution (IMPORTANT)>
Do not make connections such as for input of S/P DIF digi-
tal signals into the VF-16 DATA IN connector when “Digi-
tal In” is set to “adat”. It could result in abnormal symp-
toms such as reduction in operating speed of VF-16 and
also create noise.