Filter
Top Products
76
ACCESS
PHANTOM
CH STATUS/CH SEL
12345678
TRACK
910111213141516
TRACK
ABCDEFGH
INPUT
ORANGE
CH STATUS
INPUT RED REC GREEN PLAY MUTE
EQ/COMP
RECALL STORE
EFF1/EFF2 HI-G/F/Q
AUX1/AUX2 MID-G/F/Q
PAN LO-G
FADER CH VIEW
PRE/POST
PRE/POST
COMP
MUTE MUTE
EFF1 EFF2
DIRECT RCL MA P
SCENE
CH PARAM EDIT
EFF EDIT
OFF
CH STATUS/CH SEL
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
MASTER
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
DISP SELREC TRK
END
MARK
DIRECTBUSS
AUTO RTN
AUTO PUNCH
REC ASSIGN
REC TRKSOURCECH STATUS
AUTO PUNCH
START
SCENE SEQ.
RECORD
P.EDIT
VARI
PITCH
ALIGN SEL
SETUP
SCRUB
A RTN
A PLAY
PGM SEL
OUTOUT
LOCATE
LOC MEM
ININ
4167352
UNDO/
REDO
HOLD/ EDITSTORE
PLAYSTOP F FWDREWIND
NEXTPREV
CLIPBOARD PLAY
LOCATE ABS 0
LOCATE REC END
FADER
ADJUST
SHIFT
LEVEL
ADJUST
EXIT/NO
ENTER/YES
EJECT
JOG
SHUTTLE
2/10/B 6/14/F 7/15/G 8/16/H L R5/13/E4/12/D3/11/C1/9/A
MON OUT PHONES
UNBAL INSERTBAL UNBAL
010
PHONES
010
MON OUT
LINEMIC
PEAK
LINEMIC
PEAK
LINEMIC
PEAK
LINEMIC
PEAK
LINEMIC
PEAK
LINEMIC
PEAK
8/16/H
LINEMIC
PEAK
TRIM
INPUT
7/15/G
LINEMIC
PEAK
6/14/F5/13/E1/9/A 4/12/D3/11/C2/10/B
INSERTBAL
CLEAR
OPTICAL
DIGITAL
MULTITRACKER
TIME BASE
CLIPBOARD
ST OUT L, R
MIDI IN
MIDI Sound Source
MIDI OUT
Master Recorder
MMC
Computer System
with
MMC/MTC software
MIDI OUT
MIDI IN
MIDI OUT
MIDI IN
Connecting external equipment
1. Connect the VF-16 MIDI OUT to MIDI IN of the MIDI
sequencer.
2. Set the MIDI sequencer for “external sync mode
(EXTERNAL SYNC) by MIDI clock.”
Refer to the Owners Manual of the equipment in use for
details.
Setup of the VF-16
1. Because the MIDI clock and song position pointer will
be output from the VF-16, set the SETUP mode “MIDI sync
signal output setting” to “CLK.”
Refer to page “103”, SETUP mode “MIDI sync signal output
setting” for correct operating procedures.
2. The meter in the desired bar can be set by “Time signature
setting” of the SETUP mode.
Refer to page “99”, SETUP mode “Time Signature Setting”
for operating procedure.
3. Tempo in the desired bar can be set by “Tempo setting”
of the SETUP mode.
Refer to page “101”, SETUP mode “Tempo Setting” for
operating procedure.
4. Set the SETUP mode “Metronome setting” to “On” if click
sound is to be output according to the setup tempo map.
Refer to page “102”, SETUP mode “Metronome setting”
for operating procedure.
5. Press the [DISP SEL] key while holding down the [SHIFT]
key, and then change the time base display to BAR/BEAT/
CLK.
Confirming the MIDI clock sync
During recording and at playback following the recording,
the time base (BAR/BEAT/CLK) is displayed in accordance
to the setup tempo map, and the MIDI clock and song position
pointer is also output.
Confirm that the travel position (BAR/BEAT/CLK) of the VF-
16 and the travel position of the synchronized MIDI
sequencer are matched.
If correct sync cannot be obtained, re-check the connections/
cables and setting of both equipment.
<Note>
In the VF-16, the “ABS 0” position is set at “-002BAR/
1BEAT /00CLK.” This setting is made in consideration
of the time required (it will not sync immediately) for the
MIDI sequencer, etc. to enter into sync. As a result, if the
VF-16 is played back from ABS 0 (LOCATE ABS 0), sync
will be completed by the time it reaches the first bar, and
will thus synchronize from head of the tune.
Execution of recording
Various ways of recording can be conducted while
synchronizing the VF-16 and the MIDI sequencer with the
MIDI clock.
MTC sync/MIDI machine control system
The following will explain synchronization by the MTC (MIDI time code) output and the computer controlling
system using MMC (MIDI machine control). In this system, the VF-16 will be the master and the computer (with
sequence software) will be the slave. The VF-16 will attach any desired offset (time difference) against ABS time
(absolute time) and output it as MTC in any desired frame rate. It can also carry out the proper operation upon
receiving an MMC from outside. In this case, because the VF-16 can setup a DEVICE ID number by the SETUP
mode “MIDI Device ID Setting” menu, a multiple number of the VF-16’s can be separately controlled by changing
the DEVICE ID numbers in the transmitted message from the computer.