Filter
Top Products
Effects settings
82
3. “MFX Send” specifies the send level from each
oscillator to the master effects.
This is valid only if “BUS Select (All OSCs)” is
set to L/R or Off.
If IFX is selected for “BUS Select (All OSCs),”
the send level to the master effects is adjusted
by the “Send 1 (MFX1)” and “Send 2 (MFX2)”
parameters (PROG 8: Ed–InsertFX, Setup page)
after the signal has passed through the insert
effect.
Selecting an insert effect, and rout-
ing after the insert effect
1. Access the PROG 8: Ed–InsertFX, Setup page.
The Setup page displays the state of the routing
and the insert effect settings. In this page you
can also make “BUS Select” settings. Use the
ClickPoint to choose (All OSCs), and use the
[VALUE] dial etc. to make a selection.
2. In “Insert Effect,” select the desired insert
effect.
You can press the [CATEGORY] button and
choose an effect from six categories.
3. In “IFX On/Off,” turn the insert effect on/off.
If this is set to Off, the result will be the same as
if 00: No Effect is selected. The input sound
will be output without change.
Note: You can use the Utility “Copy Insert
Effect” to copy effect settings from another
program, etc.
4. Set the “Pan (CC#8),” “BUS Select,” “S1 (Send1
(MFX1)),” and “S2 (Send2 (MFX2))” parameters
that follow the insert effect.
“Pan (CC#8)”: Set the pan. This is valid only if
“BUS Select” is set to L/R.
“BUS Select”: Specify the output destination.
Normally you will set this to L/R. If you want
to output the sound from (INDIVIDUAL
OUTPUT) 1 and/or 2, set this to 1, 2, or 1/2.
“Send1 (MFX1),” “Send2 (MFX2)”: Set the
send level to the master effects. For this
example, set these to 127.
Pan
OSC 1
Send1
IFX BUS
IFX
MFX2
MFX1
mono
mono
Return1 / 2
Master EQ
AUDIO OUTPUT
(MAIN) L/MONO, R
BUS Select
= L/R
OSC 2
IFX / Indiv.Out
BUS Select
Insert Effect
Post IFX
Pan(CC#8)
BUS Select
Select from:
L/R
1
2
1/2
Off
Select from:
L/R
IFX
1
2
1/2
Off
Send2
stereo
Master Effects
AUDIO OUTPUT
(INDIVIDUAL)1/2
L/R BUS
stereo
mono x2
mono x 2
BUS Select
= 1/2
stereo
stereo
Chain
PROG 8: Insert FX
Post IFX
Send1 / 2
PROG 9: Master FX
BUS Select (All OSCs) = 1/2
Pan
OSC 1
Send1
IFX BUS
IFX
MFX2
MFX1
mono
mono
Return1 / 2
Master EQ
AUDIO OUTPUT
(MAIN) L/MONO, R
BUS Select
= L/R
OSC 2
IFX / Indiv.Out
BUS Select
Insert Effect
Post IFX
Pan(CC#8)
BUS Select
Select from:
L/R
1
2
1/2
Off
Select from:
L/R
IFX
1
2
1/2
Off
Send2
stereo
Master Effects
AUDIO OUTPUT
(INDIVIDUAL)1/2
L/R BUS
stereo
mono x2
mono x 2
BUS Select
= Off
stereo
stereo
Chain
PROG 8: Insert FX
Post IFX
Send1 / 2
PROG 9: Master FX
BUS Select (All OSCs) = Off
BUS Select
Pan (CC#8)
BUS SelectInsert Effect
IFX On Insert Effect
Send2(MFX2)
IFX On/Off Send1(MFX1)