Filter
Top Products
194
Insert effect algorithm list
10. BASS MULTI (Bass Guitar Multi)
This is a multi-effect designed for bass guitar. Appropriate for creating standard bass sound.
Parameter (full name) Setting Function
● COMP (Compressor): Compressor the entire output signals when the input volume exceeds a specified value.
Effect On/Off (Effect On/Off) OFF, ON This parameter turns the compressor effects on/off.
Sustain (Sustain) 0–100 Adjusts the range (time) over which low-level signals are boosted. Larger
values will result in longer sustain.
Attack (Attack) 0–100 Adjusts the strength of the attack. Larger values will result in a sharper
attack, creating a more clearly defined sound.
Level (Output Level) 0–100 Adjusts the volume.
● DEFRET (Defretter): This models a fretless bass.
Effect On/Off (Effect On/Off) OFF, ON This parameter turns the defretter effect on/off.
Sensitivity (Sens) 0–100 This controls the input sensitivity of the Defretter. It should be adjusted for the
bass guitar you have until you get the harmonic changes to sound natural.
Attack (Attack) 0–100 This controls the attack of the Defretter. Increasing the value will cause the
harmonics to change more slowly, thus producing a relatively attack-less
sound, similar to a fretless bass.
Depth (Depth) 0–100 This controls the rate of the harmonics. Increasing the value will increase
the harmonic content and therefore will create a more unusual sound.
Level (Level) 0–100 Adjusts the volume of the defretter sound.
● OCT (Octave): This adds a note one octave lower, creating a richer sound.
Effect On/Off (Effect On/Off) OFF, ON This parameter turns the octave effect on/off.
Octave Level (Octave Level) 0–100 This adjust the volume of the sound one octave below.
Direct Level (Direct Level) 0–100 This adjust the volume of the direct sound.
● ENH (Enhancer): This effect enhances the definition of the sound, and pushes it to the forefront.
Effect On/Off (Effect On/Off) OFF, ON This parameter turns the enhancer effect on/off.
Sensitivity (Sens) 0–100 Adjusts the manner in which the enhancer will be applied relative to the
input signals.
Frequency (Frequency) 1.0 –10.0 kHz Adjusts the frequency at which the enhancer effect will begin to be applied.
The effect will be made apparent in the frequencies above the frequency
set here.
Mix Level (Mix Level) 0–100 Adjusts the amount of phase-shifted sound of the range set by “Frequency”
that is to be mixed with the input.
Low Mix Level (Low Mix Level) 0–100 Adjusts the amount of phase-shifted sound of the lower range that is to be
mixed with the input.
Level (Level) 0–100 Adjusts the volume of the enhanced sound.
● EQ (Equalizer): A 4-band equalizer.
Effect On/Off (Effect On/Off) OFF, ON This parameter turns the equalizer effect on/off.
Low Gain (Low Gain) -20–+20 dB This parameter sets the gain (amount of boost or cut) for the bass equalizer.
Low-Mid Gain (Low-Mid Gain) -20–+20 dB This parameter sets the gain (amount of boost or cut) for the low-midrange
equalizer.
Low-Mid Freq (Low-Mid Freq) 100–10.0 kHz This parameter sets the central frequency for the low-midrange equalizer.
Low-Mid Q (Low-Mid Q) 0.5–16 This parameter sets the range of change in gain for the frequency set by
“Low-Mid Freq.” A larger value results in a narrower range of change.
Flanger
Pitch Shifter
Phaser
Doubling
Tr emolo/Pan
Equalizer
(*2)
Noise
Suppressor
Chorus
(*3) Delay
Octave
Enhancer
Wah
*2 Equalizer can be replaced with Wah.
Defretter
Compressor
(*1)
*3 Chorus can be replaced one of the following effects.
*1 Compressor can be replaced with Defretter.