Filter
Top Products
4
Voice Controls and Effects
DDK-7 Owner’s Manual
55
ROTARY SPEAKER
This popular effect (used mainly for electronic organ
sounds) recreates the rich, animated pulsing sound of
a rotating speaker horn.
DISTORTION
This effect adds distortion to the sound.
Effect Type Effect Type
XG ROTARY SP DUAL ROTSP 2
ROTARY SP 1 DIST+ROT SP
ROTARY SP 2 ODRV+ROT SP
ROTARY SP 3 AMP+ROT SP
ROTARY SP 4 DIST+2ROT SP
ROTARY SP 5 ODRV+2ROT SP
2WAY ROT SP AMP+2ROT SP
DUAL ROTSP 1
Parameter Value Description
EQ Low Freq. 32 - 2.0k Hz Determines the central
frequency of the low
frequency range that is
boosted or cut.
EQ Low Gain -12 - +12 dB Determines the amount over
which the low frequency
range is boosted or cut.
EQ Middle
Freq.
100 - 16k Hz Determines the central
frequency of the middle
frequency range that is
boosted or cut.
EQ Middle
Gain
-12 - +12 dB Determines the amount over
which the middle frequency
range is boosted or cut.
EQ Hi.Freq. 500 - 16k Hz Determines the central
frequency of the high
frequency range that is
boosted or cut.
EQ Hi.Gain -12 - +12 dB Determines the amount over
which the high frequency
range is boosted or cut.
Low/High
Balance
L63>H - L<H63 Determines the volume
balance between low and
high speakers.
MIC L-R Angle 0 - 180deg Determines the L/R angle of
the apparent microphone.
Dist. Drive 0 - 127 Determines the depth of
distortion. The higher the
value the greater the amount
of distortion.
Amp. Type Off, Stack, Combo,
Tube
Determines the amplifier type
simulated.
Drive 0 - 127 Determines the amount of
distortion.
Effect Type Effect Type
DIST HARD 1 V_DIST HARD
DIST HARD 2 V_DIST SOFT
DIST SOFT 1 COMP+DIST
DIST SOFT 2 XG CMP+DIST
ST DIST HARD AMP SIM
ST DIST SOFT XG AMP SIM
OVERDRIVE ST AMP SIM 1
ST OVERDRIVE ST AMP SIM 2
XG DIST XG ST AMP
XG ST DIST
Parameter Value Description
Drive 0 - 127 Determines the amount or
degree of distortion in the
sound.
Amp. Type Off, Stack, Combo,
Tube
Determines the type of
amplifier that is simulated.
LPF Cutoff 1.0 - 18kHz, Thru Determines the cutoff
frequency of the low pass
filter. Frequencies above this
value are cut or filtered out.
OutputLevel 0 - 127 Determines the level or
volume of the processed
sound.
EQ Low Gain -12 - +12 dB Determines the amount of EQ
boost or cut in the low
frequency range.
EQ Middle
Gain
-12 - +12 dB Determines the amount of EQ
boost or cut in the mid
frequency range.
Overdrive 0 - 100 % Determines the depth of
overdrive. The higher the
value the greater the amount
of distortion.
Device Transistor, Vintage,
Dist 1, Dist 2, Fuzz
Determines the device that
will create distortion:
Transistor, VintageTube,
Distortion, Fuzz and so on.
Speaker Flat, Stack, Combo,
Twin, Radio,
Megaphone
Determines the simulated
speaker type: Flat, Stack,
Combo, Twin, Radio,
Megaphone and so on.
Presence 0 - 20 Values in the higher range
can give vocals more
presence.
Comp.
Threshold
-48 - -6 db Determines the input level at
which compression begins to
be applied.
Dry/Wet D63>W - D<W63 Determines the balance of
the original sound and the
effect sound.