Filter
Top Products
51
Chapter 3
Reference
5. DISPLAY MODE
Counter display selection
P1 Location counter display selection .......................
[MBT, MSM, MSF, FreeTime]
Selects the way in which the location counter will be
displayed.
The display will change each time you press the [DIS-
PLAY MODE] key.
MBT (Measure/Beat/Tick [1/96th of a beat]/Mark*):
The location will be displayed in units of a measure
from the beginning of the song.
The tempo and time signature for display are specified
by TEMPO P1.
MSM (Minutes/Seconds/Milliseconds/Mark*): The
absolute time from the beginning of the song will be
displayed.
MSF (Minutes/Seconds/Frames [1/30th of a second]/
Mark*): The absolute time from the beginning of the
song will be displayed. (For MTC synchronization)
FreeTime (Minutes/Seconds): The remaining time
available for recording in the currently selected drive
will be displayed. Normally, this indicates the avail-
able time for monaural recording (one track). If you set
two [TRACK STATUS] indicators to REC, the available
time for stereo recording or simultaneous two-track
recording will be displayed.
* “Mark” is when the cursor is displayed under the
entire location counter. At this time, you can rotate
the [VALUE] dial to move to a mark point that you
have registered. (Refer to “■ Moving to a Mark
point” p.24)
The counter display will change as follows only during
program playback (refer to “EDIT PLAY MODE P3”).
Remaining song time
(Minutes/Seconds Millisecond [1/1000th of a second])
Elapsed song time
(Minutes/Seconds Millisecond [1/1000th of a second])
Total remaining playback time
(Minutes/Seconds Millisecond [1/1000th of a second])
Total elapsed playback time
(Minutes/Seconds Millisecond [1/1000th of a second])
6. REC MODE
Recording method select............................................
[Off, AutoPunch+RehearsalOn, AutoPunchOn, RehearsalOn]
Selects the recording method. The setting will alternate
each time you press the [REC MODE] key.
Off (indicator off): Normal recording.
AutoPunch+Rehearsal (both indica-
tors lit): Rehearsal for Auto Punch In/
Out recording will occur in the IN
(LOC1)–OUT (LOC2) area for tracks
whose [TRACK STATUS] is REC.
AutoPunch (indicator lit): Auto Punch
In/Out recording will occur in the IN
(LOC1)–OUT (LOC2) area for tracks
whose [TRACK STATUS] is REC.
Rehearsal (indicator lit): Rehearsal* for
recording will occur for tracks whose
[TRACK STATUS] is REC.
* When AutoPunch+Rehearsal or Rehearsal are
selected, when you begin recording, the input mon-
itor system (refer to SYSTEM P2) will operate in the
same way as when recording, allowing you to
rehearse the recording. Sound will not actually be
recorded.
7. PLAY MODE
Playback method select.............................................
[Off, AutoPlayOn, AutoRepeatOn]
Selects the playback method. The setting will alternate
each time you press the [PLAY MODE] key.
Off: Normal playback.
AutoPlayOn: Playback will occur between
IN (LOC1) and OUT (LOC2)*, and will
automatically stop at the OUT location.
You can also stop playback by pressing
the [STOP] key.
AutoRepeatOn: Playback will occur repeat-
edly between IN (LOC1) and OUT (LOC2)*.
You can also stop playback by pressing
the [STOP] key.
*
If you perform Auto Punch In/Out when
AutoPlayOn or AutoRepeatOn
is selected, a “pre
roll time” will be added before the IN location, and
a “post roll time” will be added after the OUT loca-
tion. (Refer to EDIT PLAY MODE P1, P2.)
For details on setting the IN and OUT locations,
refer to “Storing a Locate point” (p.23).
P1
01:SngName
01:SngName
01:SngName
01:SngName
REC
MODE
AUTO PUNCH
REHEARSAL
REC
MODE
AUTO PUNCH
REHEARSAL
REC
MODE
AUTO PUNCH
REHEARSAL
REC
MODE
AUTO PUNCH
REHEARSAL