Filter
Top Products
63
Chapter 3
Reference
29. EDIT EFFECT
Editing and saving an effect
You can edit the effect program that you selected in
EFFECT P1. Each program consists of up to four
effects.
✧ In EDIT EFFECT, repeatedly pressing the [EFFECT]
key will cycle the display through the various effects
which make up the chain, and will then display All
Effects On/Off (P1-5)
→Rename (P1-7)→Save (P1-8).
P1-1 Effect select.................(refer to “Effect program list”)
Selects the various effects which make up the effect
program which was selected in EFFECT P1.
P1-2 Effect on/off..........................................................[o, -]
Switches each effect on (o) or off (-).
P1-3 Effect parameter select.....................................
(refer to “Effect parameter list”)
Selects the effect parameter that you wish to edit.
✧ Press the [ ] key to move to the next parameter, or
press the [ ] key to move to the previous parameter.
When any parameter is displayed, you can press the
[EFFECT] key to move to the P1-1 Effect select page.
P1-4 Effect parameter value
Specifies the value of the effect parameter.
P1-5 Effect program on/off ........................................[o, -]
Turn the effect program on (o) or off (-).
The function will depend on the [EFFECT ASSIGN]
setting.
Off (-) is valid only within this page. When you move
to another page, it will automatically be turned on.
Only the effects which were turned on in P1-2 will be
turned off. When you return the setting to on (o), only
the effects which were turned on in P1-2 will be turned
back on. Also, the Monitor Delay on/off setting will
not change.
P1-6 Save destination effect program name..............
[ (blank), A...Z, a...z, 0...9, @, !, “, #, $, %, ‘, (, ), *, +, ,, -, .,
/, :, ;, <, =, >, ?, [, \, ], ^, _, {, |, }]
Input the name of the effect program that you wish to
save.
If the effect program name contains a (a symbol
which indicates a stereo input effect), and if you mod-
ify this symbol while inputting the name, it will no
longer be possible to select it again. If you wish to
retain the symbol in the name of the effect program
to be saved, begin entry following this symbol.
P1-7 Select the user effect number for the save desti-
nation
If the editing source is a user effect program U✽✽ (✽✽
is the number), the same number U✽✽ as the writing
destination number will be displayed. If the editing
source is a preset effect program, number U01 will
automatically be displayed as the writing destination
number.
Rotate the [VALUE] dial to select the memory number
in which the data will be saved, and then press and
hold the [ ] key for approximately one second. The
display will indicate “Complete” when the data has
been saved.
If you turn the power off or select another effect pro-
gram, your edits will be lost. If you wish to keep the
changes you made, you must save them.
Since the data will be written over the program which
previously occupied the save destination number, that
program will be lost.
The user area is used in common by all songs.
[EFFECT ASSIGN] Effect program OFF
INPUT 1/2 MASTER
(Global Type)
Each effect will be turned
off, and the signal will
bypass the effects.
MASTER
(Send Type)
“Snd” is
0...100
“EffRet” will be set to 0.
“Snd” is
Wet
Each effect will be turned
off, and the signal will
bypass the effects.
P1
31
4
2
4BEQ :oœ
LoG:-15dBœ
65
All Eff:o
RenøRoom
7
WriteøU01?
œ
œ