Filter
Top Products
60
Creating a Patch
PAN
(Tone Pan)
L64–63R Specifies the stereo position of the Tone. L64 places the Tone hard left, 0 puts it dead-
center and 63R pans it hard right.
* The overall panning of the entire Patch is set by the Patch Pan parameter (PATCH COM-
MON p. 46), shifting the Tone Pan values of its individual Tones leftward or rightward by
the selected amount.
PAN KF
(Tone Pan Key follow)
-100–+100 Use this parameter when you want each note’s keyboard position to affect its stereo
location. Higher settings cause a greater shifting of the Tone’s original pan position as
you move further away from Middle C (C4), where the original stereo TVA Pan value
remains in effect. Positive (+) settings cause notes above Middle C to be panned right-
ward. Negative (-) settings cause them to be panned leftward.
RANDOM PAN DEPTH
(Tone Random Pan Depth)
0–63 Use this parameter to activate random panning, note-by-note. Higher values result in
more extreme fluctuations in the Tone’s stereo placement.
ALT PAN DEPTH
(Tone Alternate Pan Depth)
L63–63R This setting causes panning to be alternated between left and right each time a key is
pressed. Higher values result in a greater left/right width. You can select the stereo
placement of the first key using this parameter—its opposite is used for the second
note, and so on back and forth. If you want to alternate the pan position of two Tones,
set them to the exact opposite L and R settings.
TVA ENVELOPE
This specifies the manner in which keyboard ve-
locity affects the times of the TVA envelope.
ENV TIME KF
(TVA Envelope Time Key follow)
-100–+100 Use this parameter when you want a note’s keyboard position to affect times T2–T4 of
the TVA envelope. Higher settings change the times by a greater amount as you move
away from Middle C (C4)—at Middle C, the original T1–T4 settings are in effect. Pos-
itive (+) settings cause the times to shorten as you play above Middle C. Negative (-)
settings cause the times to lengthen as you play above Middle C. (p. 55)
ENV T1 SENS
(TVA Envelope Time 1 Velocity
Sensitivity)
-63–+63 Use this parameter when you want keyboard playing dynamics to affect T1 (Time 1)
of the TVA envelope. If you want T1 to be sped up for strongly played notes, set this
parameter to a positive (+) value. If you want it to be slowed down, set this to a nega-
tive (-) value.
ENV T4 SENS
(TVA Envelope Time 4 Velocity
Sensitivity)
-63–+63 se this parameter when you want key release speed to affect T4 (Time 4) of the TVA
envelope. If you want T4 to be sped up for quickly released notes, set this parameter
to a positive (+) value. If you want it to be slowed down, set this to a negative (-) value.
ENV T1–T4
(TVA Envelope Time 1–4)
0–127 Specify the TVA envelope times. Higher settings lengthen the time until the next vol-
ume level is reached. (For example, T2 is the time over which L1 changes to L2.)
ENV L1–L3
(TVA Envelope Level 1–3)
0–127 Specify the TVA envelope levels. These settings specify how the volume changes at
each point, relative to the standard volume.
EFFECTS
SEND LEVEL DRY
(Dry Send Level)
Refer to p. 78.
SEND LEVEL CHO
(Tone Chorus Send Level)
SEND LEVEL REV
(Tone Reverb Send Level)
OUTPUT ASSIGN
(Tone Output Assign)
Parameter Value Description
C4C3C2C1 C5 C6 C7
0
+50
+100
-50
-100
o
L
R
Pan
Key
T1 T2 T3 T4
L3
L1
L2
Level
key is pressed key is released
Time