Filter
Top Products
125
COUNTER
Reference
SYSTEM /
USB
RECORDTRACKSONG /
CD
STOREMARKSCENETEMPO /
RHYTHM
IN / LOC1...
END / LOC4
AUTO
PUNCH
LOOPUNDOTRIGGERSCRUBENTERINPUT /
TUNER
EQ /
PHASE
INSERT
FX
MASTER
FX / AUX
SOLO /
MONITOR
METER /
Tr VIEW
Tr STATUSPANFADER
TRANSPORT
P1 Eq1–4: EQ settings for mixer
channels 1–4
Here you can apply EQ (equalizer) to the playback of tracks
1–4.
Use these settings when you wish to apply EQ to the play-
back.
The EQ has three bands. High EQ and low EQ are shelving
type, and the mid EQ is a peaking type with adjustable cutoff
frequency.
1. TrackLevelMeter .........(1, 2, 3, 4/CLP, –8, –18, –42dB)
This shows the input level from each track.
The horizontal axis indicates the channel, and the
vertical axis indicates the level.
2. HighEq.........................[(Fc=10kHz)–15.0…+15.0(dB)]
Set the high EQ gain.
You can cut/boost over a range of –15.0 – +15.0 dB at a
10 kHz cutoff frequency.
3. MidFc .........................................[100Hz...20.0k (Hz)]
Specifies the center frequency of the mid EQ.
4. MidEq...........................................[–15.0…+15.0(dB)]
Set the mid EQ gain.
You can cut/boost over a range of –15.0 – +15.0 dB at the
cutoff frequency specified by “MidFc.”
5. LowEq..........................[(Fc=100Hz)–15.0…+15.0(dB)]
Set the low EQ gain.
You can cut/boost over a range of –15.0 – +15.0 dB at a
100 Hz cutoff frequency.
6. Pair ...........................................................................
Enable pairing for adjacent mixer channels. For details,
refer to “P1 Ch1–8: Select the inputs for mixer channels
1–8” “Pair” (→p.123).
P2 Eq5–8: EQ settings for mixer
channels 5–8
Here you can apply EQ (equalizer) to the playback of tracks
5–8.
Refer to “P1 Eq1–4: EQ settings for mixer channels 1–4.”
P3 Eq9–12: EQ settings for mixer
channels 9–12
Here you can apply EQ (equalizer) to the playback of tracks
9–12.
Refer to “P1 Eq1–4: EQ settings for mixer channels 1–4.”
P4 Eq13–16: EQ settings for mixer
channels 13–16
Apply EQ (equalizer) to the playback of tracks 13–16.
Refer to “P1 Eq1–4: EQ settings for mixer channels 1–4.”
P5 Phase: Phase settings for mixer
channels
Here you can invert the phase of each channel.
This setting applies to the playback tracks. If an audio device
is input in stereo via a jack whose hot and cold conductors
are reversed, their stereo position may be blurred, or
portions of the sound may be cancelled. This setting lets you
invert the phase to correct such situations.
1. Phase ...............................................................[N, R]
N (NormalPhase): The phase of this channel will not be
inverted. Normally you will leave this at “N.”
R (ReversePhase): The phase of this channel will be
inverted.
2. Pair ...........................................................................
Enable pairing for adjacent mixer channels. For details,
refer to “P1 Ch1–8: Select the inputs for mixer channels
1–8” “Pair” (→p.123).
18. EQ/PHASE
1
324
5
6
1
2
EQ /
PHASE