Filter
Top Products
155
Troubleshooting
Appendices
Various
messages
Hard disk and
CD-R/RW drive
Specifications
MIDI implementation
chart
Block diagramEffect Program
List
Rhythm Pattern
List
Demo Song ListIndex
Can’t control the insert effect by expression pedal or
MIDI
Has a valid effect been selected for “Asn(#)” in the
[SYSTEM/USB] “Control” tab page?
→ In the [INSERT EFFECT] “InsAsn” tab page, make
sure that a valid effect has been selected in
“SelectEffType.”
Example: Situations such as when “InsEff3” is selected
for “Asn
” and “1in2out×2” is selected for
“SelectEffType” (only InsEff1 or InsEff2 can be used).
Is the correct device being used to control the effect?
→ Control the effect using the device that is selected by
the [SYSTEM/USB] “Control” tab page “Device
”
parameter. (→p.91)
For the selected effect, have you chosen effect pro-
gram number “000” (=NO EFFECT) or an effect pro-
gram that does not include a control function?
When controlling via MIDI, does the MIDI channel of
the D1600mkII match the MIDI channel of the trans-
mitting MIDI device? (→p.92)
Can’t select an “1in2outx2” insert effect
Insert effect assign may have been set to “Trk.”
→ “1in2out x2” insert effects can be selected if the
[INSERT EFFECT] “InsAsn” tab page “Assign”
parameter is set to “In.” Set this parameter to “In.”
Master effect does not apply
Is the send from each channel set to 0 or near 0?
→ In the [MASTER EFFECT/AUX] “EffSnd1” or
“EffSnd2” tab page, raise the “Send” amount.
Is the return set to 0 or near 0?
→ In the [MASTER EFFECT/AUX] “MstEff1” or
“MstEff2” tab page, raise “RetLevel” to increase the
return level.
If you are monitoring the sound from the [MONITOR
OUT L/R] jacks, has the master LR bus output been
turned off?
→ In the [SOLO/MONITOR] “Monitor” tab page, press
the “MasterLR” button to turn it “On”
Final effect does not apply
If you are monitoring the sound from the [MONITOR
OUT L/R] jacks, has the master LR bus output been
turned off?
→ In the [SOLO/MONITOR] “Monitor” tab page, press
the “MasterLR” button to turn it “On.”
External effect does not apply ([AUX OUT])
Is the external effect send set to 0 or near 0?
→ In the [MASTER EFFECT/AUX] “AuxSend” tab page,
use “Aux” to raise the external send level.
Is the output of the external effect connected to the
[INPUT 1]–[INPUT 8] jacks and assigned to a mixer
channel?
→ Use [INPUT/TUNER] “Ch1–8” or “Ch9–16” tab page
to assign the input.
Are the sub input settings correct? (→p.60, 123)
Rhythm
No rhythm sound
In the [TEMPO/RHYTHM] “Setup” tab page, is
“Rhythm” turned “Off”? (Is the [TEMPO/RHYTHM]
key dark?)
→ Turn “Rhythm” “On.”
Is the recorder stopped?
→ Press the [PLAY] key to play back. The rhythm will
sound when the recorder is recording or playing.
If you wish to check the rhythm sound while the
recorder is stopped, select the [TEMPO/RHYTHM]
“SetUp” tab page.
Did you select a silent rhythm pattern?
Has the rhythm volume been lowered?
→ In the [TEMPO/RHYTHM] “SetUp” tab page, use
“RhythmV
ol” to adjust the volume. When using the
tempo map, use the “TmpMap” tab page “Edit”
button to adjust the volume of each map.
Rhythm sound does not stop, or sounds doubled
(volume is excessive)
In the [TEMPO/RHYTHM] “SetUp” tab page, has
“Rhythm” been turned “On” ([TEMPO/RHYTHM]
key lit)?
→ Either switch “Rhythm” from “On” to “Off,” or use
“Vol” to lower the volume.
Is the rhythm selected for monitoring?
→ In the [SOLO/MONITOR] “Monitor” tab page, turn
“Rhythm” “Off.”
Is the rhythm assigned as an input?
→ In the [INPUT/TUNER] “Ch1–8” or “Ch9–16” tab
page, do not assign “Rhythm L” or “Rhythm R” to a
channel. Alternatively, lower the fader of the channel
that the rhythm is assigned to.
Pressing a key does not perform the
function
Some keys do not function when the recorder is play-
ing or recording.
→ Stop the recorder, and then perform the operation.
Some keys do not function while scrub is turned on.
→ Turn off Scrub, and then perform the operation.
(→p.122)
Could the screen be displaying a dialog box?
→ Press the “Yes,” “No,” “OK,” or “Cancel” button to
close the dialog box.
MIDI
MIDI sequencer does not synchronize/MIDI control is
not possible
Is the MIDI cable connected correctly? (→p.7, 87)
Is the MIDI cable broken?
Can’t synchronize using MTC or MIDI Clock
Has the D1600mkII been set as the master and the
MIDI sequencer as the slave? (→p.87, 92)
Does the synchronization signal transmitted by the
D1600mkII match the synchronization signal received
by the MIDI sequencer?
→ Check “Select MIDISync Mode.” (→p.87, 92)
Troubleshooting