Filter
Top Products
158
Illegal Fat Number
Some of the data in the hard disk has been damaged
for some reason.
→ Delete all songs for which this message appears. If the
message still appears, format the hard disk. (→p.70,
82, 97)
When you turn off the power, be sure to use the cor-
rect procedure. (→p.11)
Illegal Mark Point
When using Disc At Once to write an audio CD, leave
at least four seconds between marks.
→ You must also leave at least four seconds between the
following points.
•From the beginning of the track to the first mark.
•From the mark immediately before the end time of
the track you are writing to CD until the end of the
track.
Illegal To-End Time
When using the track editing command “Exp/
CompTrack,” the TO and END region cannot be
executed for the specified IN–OUT region.
→ You must set the TO–END region to be within 50–
200% of the IN–OUT region.
InTime>=OutTime
The IN and OUT settings you made for track editing,
auto punch-in/out recording, or looping are incorrect,
and cannot be executed. This message will appear if
IN is later than OUT, or if they are at the same time
location.
→ Set the IN and OUT times correctly.
Memory Full
There is insufficient memory for recording or track
editing.
→ Delete unneeded data.
Alternatively, you may be able to solve this problem
by shutting-down the D1600mkII and starting it up
again.
MIDI Overflow
When receiving MMC or recording MIDI Clock,
reception of MIDI data failed.
→ Delete any unnecessary data that the transmitting
device might be sending.
No CDRW Disc
The media you are attempting to erase is not a CD-
RW.
→ Execute the Erase operation on a CD-RW.
No Disc
CD media is not inserted.
No Drive/No Disk
→ “AE Timeout.”
No Event
When writing to audio CD, tracks 1 and 2 did not
contain audio data.
→ Bounce the data to be written to CD onto tracks 1 and
2.
No internal hard disk drive
The internal hard disk cannot be detected.
→ Install the internal hard disk. If it is already installed,
check the installation once again.
→ If the CD-R/RW drive is installed, check the installa-
tion of the CD-R/RW drive.
Number Of Tracks
When performing a track editing operation, there is a
different number of source and destination tracks.
→ Specify the same number of tracks for the source and
destination.
Copying is not possible because “Clip” contains no
data.
→ Either copy data into “Clip,” or select a different copy-
source track.
SameFileNameExists
When exporting a WAV file or backing up to the USB
drive, a file of the same name already exists in the
export-destination drive.
→ Change the file name. (→p.35, 80)
Song Protected
The selected song is protected.
→ Either defeat the protect setting (→p.70) or select a
different song. (→p.35)
→ If you are formatting, turn the “Force” button “On.”
(→p.82, 97)
System Error
→ “AE Timeout.”
Tempo Fast
When recording tempo, recording failed because the
tempo was too fast.
→ If you are recording MIDI Clock, set your sequencer or
other MIDI output device to a slightly slower tempo.
→ If you are recording tap input, tap a bit slower.
Tempo Slow
When recording tempo, recording failed because the
tempo was too slow.
→ If you are recording MIDI Clock, set your sequencer or
other MIDI output device to a tempo of =40 or
higher.
→ If you are recording tap input, tap a bit faster.
ToTime>=EndTime
There is a problem with the TO and END settings you
made for the track editing operation “Exp/
CompTrack,” and the operation cannot be executed.
This message will appear if TO is later than END or at
the same location.
→ Set the times correctly.
Track Full
When writing an audio CD, the number of tracks
(songs) written to the CD has exceeded 99.
→ Write the songs to new CD media.
Unsupported File Type
When importing a WAV file, you attempted to import
a file that was other than an 8/16/24-bit 44.1 kHz
monaural/stereo file.
→ Select an 8/16/24-bit 44.1 kHz monaural/stereo file.
Write CD Failed
Failed to write the CD.
→ Try writing to CD-R/RW at a slower speed.