Filter
Top Products
67
ZOOM B9.1ut
Effect Types and Parameters
Splitter
This effect divides the signal into two bands (high/low) and lets you freely adjust the mixing ratio of the two bands.
PARM1 PARM2 PARM3 PARM4
Hi Mix
0 – 100
Low Mix
0 – 100
Frequency
80 – 2.5k
Level
2 – 100
Adjusts the mixing ratio of the high
frequency band.
Adjusts the mixing ratio of the low
frequency band.
Adjusts the crossover point
between the high frequency and
low frequency band.
Adjusts the signal level after
passing the module.
PedalVox
This simulation effect is modeled on vintage Vox pedal wah.
PedalWah
This is a pedal wah effect for bass guitar.
The above two effect types have the same parameters.
PARM1 PARM2 PARM3 PARM4
Position
Befr, Aftr
Frequency
1 – 50
DryMix
0 – 100
Level
2 – 100
See "A-Resonance (Auto
Resonance)" (→ p. 65).
Adjusts the frequency that is
emphasized. When the expression
pedal is not used, the effect is
similar to a half open pedal.
Adjusts the original sound mixing
ratio.
Adjusts the signal level after
passing the module.
P-Resonance (Pedal Resonance)
Pedal wah with a strong character.
PARM1 PARM2 PARM3 PARM4
Position
Befr,Aftr
Frequency
1 – 50
Resonance
0 – 10
Level
2 – 100
See "A-Resonance (Auto
Resonance)" (→ p. 65).
Adjusts the modulation frequency.
Adjusts the intensity of the effect
character.
Adjusts the signal level after
passing the module.
X-Wah
This effect allows cross-fading of original sound and effect sound (Vox type wah), using the pedal or another control source. Try assigning the
vertical direction of the Z-pedal (PV1 – PV4) to the "Frequency" parameter and the horizontal direction (PH1 - PH4) to the "X-Fade" parameter.
PARM1 PARM2 PARM3 PARM4
Position
Befr, Aftr
Frequency
1 – 50
X-Fade
0 – 100
Level
2 – 100
See "A-Resonance (Auto
Resonance)" (→ p. 65).
Adjusts the modulation frequency.
Adjusts the balance between
original sound and effect sound.
Adjusts the signal level after
passing the module.
X-Phaser
This effect allows cross-fading of original sound and effect sound (phaser), using the pedal or another control source. Try assigning the vertical
direction of the Z-pedal (PV1 - PV4) to the "Rate" parameter and the horizontal direction (PH1 - PH4) to the "X-Fade" parameter.
PARM1 PARM2 PARM3 PARM4
Color
Bef1 – 4,
Aft1 – 4
Rate
0 – 50
X-Fade
0 – 100
Level
2 – 100
Selects the connection position and
sound type. The "Bef1" – "Bef4"
settings place the effect before the
PRE-AMP module and the "Aft1" –
"Aft4" settings after the PRE-AMP
module.
Adjusts the modulation rate.
Adjusts the balance between
original sound and effect sound.
Adjusts the signal level after
passing the module.
X-Vibe (X Vibrato)
This effect allows cross-fading of phaser sound and tremolo sound, using the pedal or another control source. Try assigning the vertical direction
of the Z-pedal (PV1 - PV4) to the "PHA Rate" or "TRM Rate" parameter and the horizontal direction (PH1 - PH4) to the "X-Fade" parameter.
PARM1 PARM2 PARM3 PARM4
PHA Rate
0 – 50
TRM Rate
0 – 50
X-Fade
0 – 100
Level
2 – 100
Adjusts the modulation rate of the
phaser effect.
Adjusts the modulation rate of the
tremolo effect.
Adjusts the balance between phaser
sound and tremolo sound.
Adjusts the signal level after
passing the module.