Filter
Top Products
79
ZOOM B9.1ut
Effect Types and Parameters
TOTAL module
This module comprises parameters that affect the entire patch.
TOTAL
Specifi es the patch specifi c level, tempo, and balance settings.
PARM1 PARM2 PARM3
PatchLevel
2 – 100
TotalBal
0 – 100
Tempo
40 – 250
Specifi es the overall level of the
patch.
Specifi es the mixing balance
between the sound routed through
the effect module and the direct
sound.
Specifi es the patch specifi c tempo
(→ p. 38).
NAME
Specifi es a name for the patch (
→
p. 26).
ARRM (Page 1)
Makes settings for the ARRM function (
→
p. 52). To bring up the second page of settings, turn the [TYPE] knob clockwise while the ARRM control
target is set to an option other than "NOT Assign".
PARM1 PARM2 PARM3
ARRM
min (minimum value)
See page 52
MAX (maximum
value)
See page 52
ARRM control target
Selects the ARRM control target.
When "NOT Assign" is selected,
the ARRM function is disabled.
Specifi es the parameter value that
is set when the control waveform
reaches its lowest point.
Specifi es the parameter value that
is set when the control waveform
reaches its highest point.
ARRM (Page 2)
To return to the fi rst page of settings, turn the [TYPE] knob counterclockwise.
PARM1 PARM2
Wave
See page 53
Sync
See page 53
Selects the control target
waveform.
Specifi es control waveform
synchronization using the patch
specifi c tempo as reference.
PV1 to PV4 (expression pedal vertical direction setting)
Specify control targets 1 - 4 for vertical direction movement of the expression pedal.
PH1 to PH4 (expression pedal horizontal direction setting)
Specify control targets 1 - 4 for horizontal direction movement of the expression pedal.
The above eight effect types have the same parameters. However, for PH1 to PH4 (expression pedal horizontal direction setting), PARM4 (module on/
off) is not available.
PARM1 PARM2 PARM3 PARM4
Expression pedal control target
min (minimum value) Max (maximum value) Module on/off function
Specifi es the expression pedal
control target.
Specifi es the parameter value that
is set when the pedal is fully raised,
or when it is fully turned to the left.
Specifi es the parameter value that
is set when the pedal is fully
pushed down, or when it is fully
turned to the right.
Enables or disables the module on/
off function. This parameter is not
available for the horizontal
direction (PH1 to PH4).
FuncSW Assign (Function Foot Switch Assignment)
Specifi es the operation of function foot switches 1 – 3.
PARM1 PARM2 PARM3
FuncSW1 Assign (Function
Foot Switch 1 Assignment)
FuncSW2 Assign (Function
Foot Switch 2 Assignment)
FuncSW3 Assign (Function
Foot Switch 3 Assignment)
Specifi es the operation performed
by function foot switch 1.
Specifi es the operation performed
by function foot switch 2.
Specifi es the operation performed
by function foot switch 3.
FootSW Assign (Foot Switch Assignment)
Specifi es which module is turned on and off by function foot switches 1 - 4 in manual mode.
PARM1 PARM2 PARM3 PARM4
Foot Switch 1
CMP, WAH
Foot Switch 2
ExL, AMP
Foot Switch 3
EQ, MOD
Foot Switch 4
DLY, REV
Selects the module to be turned on/
off by foot switch 1.
Selects the module to be turned on/
off by foot switch 2.
Selects the module to be turned on/
off by foot switch 3.
Selects the module to be turned on/
off by foot switch 4.