Filter
Top Products
73
ZOOM B9.1ut
Effect Types and Parameters
Step
Special effect that changes the sound in a staircase pattern.
PARM1 PARM2 PARM3 PARM4
Depth
0 – 100
Rate
0 – 50
Resonance
0 – 10
Shape
0 – 10
Adjusts the modulation depth. Adjusts the modulation rate. Adjusts the resonance intensity. Adjusts the effect sound envelope.
Delay
This is a delay with a maximum setting of 2000 ms.
TapeEcho
This effect simulates a tape echo.
The above two effect types have the same parameters.
PARM1 PARM2 PARM3 PARM4
Time
1 –
2000ms
FeedBack
0 – 100
HiDamp
0 – 10
Mix
0 – 100
Sets the delay time.
Adjusts the amount of feedback.
Higher setting values result in a
higher number of delay sound
repetitions.
Adjusts the treble attenuation of the
delay sound. Higher setting values
result in softer delay sound.
Adjusts the level of the effect sound
mixed to the original sound.
DynamicDelay
This is a dynamic delay where the effect volume varies according to the input signal level.
PARM1 PARM2 PARM3 PARM4
Time
1 –
2000ms
Amount
0 – 100
FeedBack
0 – 100
Sense
-10 – 10
Sets the delay time.
Adjusts the level of the effect sound
mixed to the original sound.
Adjusts the amount of feedback.
Adjusts the effect sensitivity. With
positive setting values, the effect
sound level increases at higher
input signal levels. With negative
setting values, the effect sound
level decreases at higher input
signal levels.
DynamicFlang (Dynamic Flanger)
This is a dynamic fl anger where the effect volume varies according to the input signal level.
PARM1 PARM2 PARM3 PARM4
Depth
0 – 100
Rate
0 – 50
Resonance
-10 – 10
Sense
-10 – 10
Adjusts the modulation depth. Adjusts the modulation rate. Adjusts the resonance intensity.
Adjusts the effect sensitivity. With
positive setting values, the effect
sound level increases at higher
input signal levels. With negative
setting values, the effect sound
level decreases at higher input
signal levels.
MonoPitch
This is a pitch shifter specially for monophonic sound (single-note playing), with little sound fl uctuation.
PARM1 PARM2 PARM3 PARM4
Shift
-12 – -1, dt,
1 – 12, 24
Tone
0 – 10
Fine
-25 – 25
Balance
0 – 100
Adjusts the pitch shift amount in
semitones. (dt=detuned)
Adjusts the tonal quality of the
sound.
Allows fi ne adjustment of pitch
shift amount in Cent (1/100
semitone) steps.
Adjusts the balance between
original sound and effect sound.
H.P.S (Harmonized Pitch Shifter)
This is an intelligent pitch shifter that automatically generates the effect sound according to a preset key and scale.
PARM1 PARM2 PARM3 PARM4
Scale
-6 – 6
Key
C – B
Tone
0 – 10
Mix
0 – 100
Determines the interval for the
pitch-shifted sound (see Table 4).
Determines the key note of the
scale used for pitch shifting (see
Table 3).
Adjusts the tonal quality of the
sound.
Adjusts the level of the effect sound
mixed to the original sound.
[Table 4]
Setting Type of scale Interval Setting Type of scale Interval Setting Type of scale Interval
-6
Major scale
Sixth down 3
Major scale
Third up -m
Minor scale
Third down
-5 Fifth down 4 Fourth up m Third up
-4 Fourth down 5 Fifth up
-3 Third down 6 Sixth up