Filter
Top Products
119
Chapter 8 Parameters Guide
Chapter
8
This effect adds delayed sound to the direct sound, giving
more body to the sound or creating special effects.
DELAY
Parameter/
Range
Explanation
DELAY ON/OFF
Off, On
Turns the DELAY Effect on/off.
Pressing [DELAY] switches On and Off.
Type
This selects which type of delay.
• If you switch patches with the Type set to either Dual-S, Dual-P, or Dual-
L/R and then begin to play immediately after the patches change, you
may be unable to attain the intended effect in the first portion of what
you perform.
• The stereo effect is cancelled if a monaural effect or COSM amp is
connected after a stereo delay effect.
Single
This is a simple monaural delay.
Pan
This delay is specifically for stereo output. This
allows you to obtain the tap delay effect that di-
vides the delay time, then deliver them to L and
R channels.
fig.04-050
Stereo
The direct sound is output from the left chan-
nel, and the effect sound is output from the
right channel.
Dual-S
(Dual Series)
This is a delay comprising two different delays
connected in series. Each delay time can be set
in a range from 1 ms to 1700 ms.
fig.04-051
Dual-P
(Dual Parallel)
This is a delay comprising two delays connect-
ed in parallel. Each delay time can be set in a
range from 1 ms to 1700 ms.
fig.04-0070
Dual-L/R
This is a delay with individual settings avail-
able for the left and right channels. Delay 1 goes
to the left channel, Delay 2 to the right.
fig.04-0080
Reverse
This produces an effect where the sound is
played back in reverse.
Analog
This gives a mild analog delay sound. The de-
lay time can be set within the range of 1 to 3400
ms
STEREO
INPUT
OUTPUT L
OUTPUT R
Feedback
Dly Time
EffectLev
DELAY
Tap Time
D1 D2
D1: Delay1
D2: Delay2
D1
D2
D1
D2
L
R
Tape
This setting provides the characteristic waver-
ing sound of the tape echo. The delay time can
be set within the range of 1 to 3400 ms.
Warp
This simultaneously controls the delay sound’s
feedback level and volume to produce a totally
unreal delay.
fig.04-0050
Modulate
This delay adds a pleasant wavering effect to
the sound.
DELAY Common Parameters
Parameter/
Range
Explanation
Dly Time (Delay Time)
1ms–3400ms,
BPM –BPM
This determines the delay time.
When set to BPM, the value of each parameter will be set according
to the value of the “Master BPM” (p. 122) specified for each patch.
This makes it easier to achieve effect sound settings that match the
tempo of the song.
• If, due to the tempo, the time is longer than the range of allowable
settings, it is then synchronized to a period either 1/2 or 1/4 of that time.
• If you tap [CATEGORY/ENTER], the delay time will change to match
the timing of your tapping.
Feedback
0–100
This sets the amount of delay sound re-
turned to the input.
A higher value will increase the number of
the delay repeats.
Feedback is returning a delay signal to the
input.
High Cut (High Cut Filter)
700Hz–11.0kHz,
Flat
This sets the frequency at which the high
cut filter begins to take effect. When “Flat”
is selected, the high cut filter will have no
effect.
EffectLev (Effect Level)
0–120
Adjusts the volume of the delay sound.
DirectLev (Direct Level)
0–100
Adjusts the volume of the direct sound.
Parameter/
Range
Explanation
INPUT
OUTPUT
F.B. Depth
Level
Dep
DELAY
Rise Time
GT-10B_e.book 119 ページ ２００８年２月２６日 火曜日 午後３時３０分