Filter
Top Products
137
Chapter 8 Parameters Guide
Chapter
8
Pdl Indicate (Pedal Indicate)
You can have all unlit pedal indicators flash faintly instead.
Off The Pedal Indicate function is not use.
On All unlit pedal indicators flash.
Num Pdl Sw (Number Pedal Switch)
This allows you to call up various features by pressing the pedals
with the same numbers as the currently selected patches.
Off This function is not operational.
Tuner Switches the Tuner on and off.
Ch. A/B Switches between effect channel A and B.
Dial Func (Dial Function)
This setting determines whether or not rotating the dial switches the
patches.
Pat&Val
The dial is used both for switching patches and
changing the value of settings. In addition to
switching patches with the pedals, you can also
switch them by rotating the dial.
Value
The dial is used only for changing the values of set-
tings.
Parameter/
Range
Explanation
CONTROLLER
Parameter/
Range
Explanation
SYS KNOB SETTING (System Knob Setting)
Knob P1–P4
COMP:CS:Sus, COMP:CS:Atk,
COMP:LM:Thres, COMP:LM:Rel,
COMP:MB:LoThr, COMP:MB:HiThr,
COMP:NA:Drive, COMP:Tone, COMP:Level,
ODDS:Drive, ODDS:Tone,
ODDS:EfectLev, PRE:Gain, PRE:Level,
PRE:Bass, PRE:Mid, PRE:Treble,
PRE:Presnce, PRE:Mic Lev, EQ:Low Cut,
EQ:Low Gain, EQ:Lo-MidGain,
EQ:Hi-MidGain, EQ:High Gain,
EQ:High Cut, DELAY:Time,
DELAY:Feedbak, DELAY:Hi Cut,
DELAY:EfctLev, DELAY:D1(2)Time,
DELAY:D1(2)Fbk, DELAY:D1(2)HCut,
DELAY:D1(2)Lev, CHORUS:Rate,
CHORUS:Depth, CHORUS:PreDly,
CHORUS:E.Lev, REVERB:Time,
REVERB:Hi Cut, REVERB:E.Lev,
MASTER:Low, MASTER:Mid,
MASTER:High, Patch Level,
PDL:Wah E.Lev, PDL:PB E.Lev,
SR:Send Level, SR:Rtn Level,
NS1(2):Threshold, NS1(2):Release,
GLOBAL EQ:Low, GLOBAL EQ:Mid,
GLOBAL EQ:Hi
EXP1/2 PEDAL SETTING
Prefernc (Preference)
Patch
The patch pedal setting is used. This allows
you to use different pedal settings in each
individual patch.
System
The CONTROLLER screen’s pedal setting
(Function, Min and Max) is used. This ap-
plies the same pedal settings to all patches.
Function
Off
The function is not assign to the controller.
Foot Volume Controls the Foot Volume.
Pedal Bend *1 Controls the Pedal Bend.
WAH *1 Controls the WAH.
PB/FV *1 Controls the Pedal Bend or Foot Volume.
WAH/FV *1 Controls the WAH or Foot Volume.
Patch Level Controls the Patch Level.
*1 This parameter is enabled in EXP1 PEDAL SETTING.
Min (Minimum)
0–100
0–200 (Function =
Patch Level)
This sets the minimum value for the range
in which the parameter can change.
Max (Maximum)
0–100
0–200 (Function =
Patch Level)
This sets the maximum value for the range
in which the parameter can change.
GT-10B_e.book 137 ページ ２００８年２月２６日 火曜日 午後３時３０分