Filter
Top Products
136
Chapter 8 Parameters Guide
MANUAL MODE SETTING
Parameter/
Range
Explanation
Number Pedal 1–4, BANK
▼
Pedal, BANK
▲
Pedal
The Number pedal and the BANK pedal are used for
switching specified effects on and off.
Off
The function is not assign to the pedals.
Ch.A/B
Switches between effect channel A and B.
Comp Switches the COMP on and off.
OD/DS Switches the OD/DS on and off.
Preamp Switches the PREAMP/SPEAKER on and off.
EQ Switches the EQ on and off.
FX1 Switches the FX-1 on and off.
FX2 Switches the FX-2 on and off.
Delay Switches the DELAY on and off.
Chorus Switches the CHORUS on and off.
Reverb Switches the REVERB on and off.
PdlFX Switches the PEDAL FX on and off.
S/R Switches the SEND/RETURN on and off.
AmpCtl Switches the Amp Control on and off.
Tuner
Switches the TUNER on and off.
PL Switches the PHRASE LOOP on and off.
PL R/P Records/plays back the phrase.
PL Clr Clears the phrase.
PL M/P Mutes playback of the phrase.
BPMTap Used for tap input of the Master BPM.
DlyTap Used for tap input of the delay time.
MIDI
Controls the Start/Stop of external MIDI devic-
es (such as sequencers).
MMCPly
Controls the Play/Stop of external MIDI devic-
es (such as hard disk recorders).
Lev+10 Increases the patch volume level by 10 units.
Lev+20 Increases the patch volume level by 20 units.
Lev-10 Decreases the patch volume level by 10 units.
Lev-20 Decreases the patch volume level by 20 units.
NumInc
Switches to the next higher patch number in the
same bank as the currently selected patch.
NumDec
Switches to the next lower patch number in the
same bank as the currently selected patch.
BnkInc Switches to the next higher bank number.
BnkDec Switches to the next lower bank number.
PLAY OPTION
Parameter/
Range
Explanation
Preamp Mode
Patch
The patch preamp setting is used. This allows you to
use different preamp settings in each individual patch.
System1–3
The system’s preamp setting is used. This applies
the same preamp settings to all patches.
Pressing EZ TONE [CREATE] automatically switches
Preamp Mode to Patch.
Patch ChgMode (Patch Change Mode)
This setting determines whether or not the decay of reverb, delay, and
similar effects continue when patches are switched on the GT-10B.
Fast
Patches are changed normally. The unit switches to
the subsequent patch without any carry-over of the
decay from the previous patch’s reverb or delay.
Smooth
The unit switches to the subsequent patch with the
decay from the previous patch’s reverb or delay
continued after the switch is made.
To ensure smooth switching, the patches may be switched
with a delay of one tempo beat.
Bank Chg Mode
This sets the timing with which the GT-10B switches to the next
patch when switching banks with the pedals.
Wait
Although the indication in the display is updated to
reflect the change in the bank when a BANK pedal
is pressed, the patch will not change until a number
pedal has been pressed.
Immed
The patch switches instantly when a BANK pedal
or any of the number pedals is pressed.
BankExtentMin (Bank Extent Minimum)
P01–P50,
U01–U50
Sets the lower limit for the banks.
BankExtentMax (Bank Extent Maximum)
P01–P50,
U01–U50
Sets the upper limit for the banks.
EXP Pdl Hold (Expression Pedal Hold)
This setting determines whether or not the Assign’s (p. 51) opera-
tional status is carried over to the next patch when patches are
switched.
Off
The Assign’s operational status is not carried over.
(Example)
If a patch is switched while the volume is being con-
trolled with an EXP Pedal, the volume of the subse-
quent patch is set to the value set in that patch.
If the EXP Pedal is operated, the volume will
change in accord with the pedal’s movement.
On
The Assign’s operational status is carried over.
(Example)
If a patch is switched while the volume is being con-
trolled with the EXP Pedal, the volume of the sub-
sequent patch will take on the value determined by
the current pedal position (angle). If the patch
switched to has the EXP Pedal controlling the wah
effect, then the volume assumes the value set in the
patch, and the patch’s wah effect is given the value
derived from the current pedal position (angle).
GT-10B_e.book 136 ページ ２００８年２月２６日 火曜日 午後３時３０分