Filter
Top Products
139
Chapter 8 Parameters Guide
Chapter
8
DELAY:D1:Time
DELAY D1TIM D1 TIM
DELAY:D1:Fbk DELAY D1FBK D1 FBK
DELAY:D1:HCut DELAY D1HC D1 HC
DELAY:D1:Lev DELAY D1LEV D1 LEV
DELAY:D2:Time DELAY D2TIM D2 TIM
DELAY:D2:Fbk DELAY D2FBK D2 FBK
DELAY:D2:HCut DELAY D2HC D2 HC
DELAY:D2:Lev DELAY D2LEV D2 LEV
CHORUS:Rate CHORS RATE CE RAT
CHORUS:Depth CHORS DEPTH CE DPT
CHORUS:PreDly CHORS P DLY CE DLY
CHORUS:E.Lev CHORS E LEV CE LEV
REVERB:Time REVRB TIME RV TIM
REVERB:Hi Cut REVRB H CUT RV HC
REVERB:E.Lev REVRB E LEV RV ELV
MASTER:Low MST LOW MT LOW
MASTER:Mid MST MID MT MID
MASTER:High MST HIGH MT HI
Patch Level PATCH LEVEL PAT LV
PDL:WAH:E.Lev PEDAL WAH E WA ELV
PDL:PB:E.Lev PEDAL PB E PB ELV
SR:Send Level SR S LEV SR SND
SR:Rtn Level SR R LEV SR RTN
NS1:Threshold NS1 THRES N1 THR
NS1:Release NS1 RELE N1 REL
NS2:Threshold NS2 THRES N2 THR
NS2:Release NS2 RELE N2 REL
GLOBAL EQ:Low GBEQ LOW GB LOW
GLOBAL EQ:Mid GBEQ MID GB MID
GLOBAL EQ:Hi GBEQ HIGH GB HI
Display with SYS
KNOB SETTING
Display at Play
screen 1
Display at the
bottom of the
Play screen
LCD
Parameter/
Range
Explanation
Contrast
1–16
Adjusts the contrast.
MIDI
Parameter/
Range
Explanation
Rx Channel (Receive Channel)
1–16ch
This sets the MIDI channel used for receiving
MIDI messages.
Omni Mode
Omni Off,
Omni On
When set to “Omni On,” messages are received
on all channels, regardless of the MIDI channel
settings.
Tx Channel (Transmit Channel)
1–16ch, Rx
This sets the MIDI Transmit channel used for
transmitting MIDI messages. When set to “Rx,”
this MIDI channel is same as the Rx Channel
parameter (Receive channel).
Device ID
1–32
This sets the Device ID used for transmitting
and receiving Exclusive messages.
Sync Clock
This setting determines the basis used for synchronizing the timing
for effect modulation rates and other time-based parameters.
• When you have an external MIDI device connected, the Master BPM is
then synchronized to the external MIDI device’s tempo, thus disabling
the Master BPM setting. To enable setting of the Master BPM, set to
“Internal.”
• When synchronizing performances to the MIDI Clock signal from an
external MIDI device, timing problems in the performance may occur
due to errors in the MIDI Clock.
Auto
When the MIDI Clock of the external MIDI de-
vice is not being received, the performance is
synchronized to the tempo set in MASTER
BPM; when the external MIDI device’s MIDI
Clock is being received from the USB or MIDI
IN connector, the performance is synchronized
to that.
Internal
The performance is synchronized to the tempo
set in MASTER BPM.
PC Out (Program Change Out)
This setting determines whether or not Program Change messages
are output when patches are switched on the GT-10B.
Off
Program Change messages are not output,
even when patches are switched.
On
Program Change messages are simultaneously
output when patches are switched.
GT-10B_e.book 139 ページ ２００８年２月２６日 火曜日 午後３時３０分