Filter
Top Products
58
Recorder Functions
DIGITAL MULTITRACKER
LOCATE ABS 0
LOCATE REC END
SEL
TIMEBASE
CURSOR
PHANTOM
ACCESS
PEAK
CH ON/OFF
LR
GUITAR
GUITAR
LINE MIC LINE MIC MIN MAX
MASTERING TRAINING
EFFECTEQPAN
SCENE SEQ.SCENE
TRACK
UNDO
SETUP
PUNCH
AUTO
LOOP PITCH SCRUB
VARI
F FWDREWINDPLAYSTOPRECORD
EXIT
ENTER
TRIMTRIM
WAVE FORM
MIX PARAMETER
PGM
FADER
MAP
ON/OFF
2TRK MODE
F1
F2
F3
SHIFT
EDIT
EDIT EDIT
MARK
DELETE
LOCATE
FOOT SW
ST OUT
PHONES
INPUT A
BOUNCE
INPUT B
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
+6
-10
-20
-40
-
∞
-30
0
PEAK
CH ON/OFF
2 3 4
5 6
7/8 2TRK1
MASTER
TRACK STATUS / TRACK SEL
TRACK STATUS
RED
REC
GREEN
PLAY
OFF
MUTE
STATUS
/SEL
EJECT
/YES
/NO
SHUTTLE
JOG
UNBAL
UNBAL
BAL
BAL
F1
F2 F3
EDIT
/REDO
REC EFF
1
2
3
3
4
5
4
5
1
2
1
Vari Pitch
You can alter the playback or recording speed of the recorder within +/- 6.0 % range in 0.1 % increments/dec-
rements by using the vari pitch function. With the vari pitch function, the pitch changes according to the speed.
Turning on or off the vari pitch function
Press the [VARI PITCH/EDIT] key.
The key lights up in green, showing the vari pitch func-
tion is active.
Press the [VARI PITCH/EDIT] key again.
The key turns off, showing the vari pitch function is not
active.
<Note>
You can turn on or off the vari pitch function while
stopped or during playback, however, you cannot turn
on or off the function during recording.
Setting the speed
You can adjust the speed while stopped or during
playback, however, you cannot adjust the speed dur-
ing recording. If you adjust the speed during play-
back with the vari pitch function active, you can moni-
tor the result of speed (pitch) change while adjusting.
While stopped or during playback, press the [VARI
PITCH/
EDIT] key while holding down the [SHIFT] key.
The current pitch value is highlighted, showing that the
value can be edited.
"ON" or "OFF" (of the vari pitch function) is also shown
on the screen.
Use the [JOG] dial to enter the pitch value.
Press the [EXIT/NO] key to return to the Normal screen.
<Notes>
• Even if the pitch value is set to 0.0 % (no speed
change), pressing the
[VARI PITCH]
key turns on the
vari pitch function.
In such a condition, the function is active but the
speed is not changed.
• The vari pitch function automatically turns off by
carrying out any of the following.
1.Turning the power off and then on. (The pitch
value is also reset to 0.0 %.)
2.Setting the slave mode to "On" in the setup mode.
(The pitch value is retained.)
Note that you cannot turn on the vari pitch
function when the slave mode is "On".
3.Setting the digital input to "On" in the setup mode
("DIGI IN" is shown on the screen).
Note that you cannot turn on the vari pitch
function when the digital input is selected.