Filter
Top Products
10
Important Notes
561
• Use only the specified expression pedal (EV-5/7; sold separately). By
connecting any other expression pedals, you risk causing malfunction
and/or damage to the unit.
562
• Some connection cables contain resistors. Do not use cables that
incorporate resistors for connecting to this unit. The use of such
cables can cause the sound level to be extremely low, or impossible to
hear. For information on cable specifications, contact the manufac-
turer of the cable.
565
• Before opening or closing the keyboard lid, always make sure that no
pets or other small animals are located on top of the instrument (in
particular, they should be kept away from the keyboard and its lid).
Otherwise, due to the structural design of this instrument, small pets
or other animals could end up getting trapped inside it. If such a
situation is encountered, you must immediately switch off the power
and disconnect the power cord from the outlet. You should then
consult with the retailer from whom the instrument was purchased, or
contact the nearest Roland Service Center.
Floppy Disk Handling
(Using Optional Floppy Disk Drive)
651
• Floppy disks contain a plastic disk with a thin coating of magnetic
storage medium. Microscopic precision is required to enable storage
of large amounts of data on such a small surface area. To preserve
their integrity, please observe the following when handling floppy
disks:
• Never touch the magnetic medium inside the disk.
• Do not use or store floppy disks in dirty or dusty areas.
• Do not subject floppy disks to temperature extremes (e.g., direct
sunlight in an enclosed vehicle). Recommended temperature
range: 10 to 50˚C (50 to 122˚F).
• Do not expose floppy disks to strong magnetic fields, such as
those generated by loudspeakers.
652
• Floppy disks have a “write protect” tab which can protect the disk
from accidental erasure. It is recommended that the tab be kept in the
PROTECT position, and moved to the WRITE position only when you
wish to write new data onto the disk.
fig.DiskProtect.e.eps
653
• The identification label should be firmly affixed to the disk. Should the
label come loose while the disk is in the drive, it may be difficult to
remove the disk.
654
• Store all disks in a safe place to avoid damaging them, and to protect
them from dust, dirt, and other hazards. By using a dirty or dust-
ridden disk, you risk damaging the disk, as well as causing the disk
drive to malfunction.
USB Memory Handling
704
• When connecting USB memory, firmly insert it all the way in.
705
• Do not touch the pins of the USB memory connector, or allow them to
become dirty.
708
• USB memory is made using high-precision electronic components, so
please observe the following points when handling it.
• To prevent damage from static electrical charges, discharge any
static electricity that might be present in your body before
handling USB memory.
• Do not touch the terminals with your fingers or any metal object.
• Do not bend or drop USB memory, or subject it to strong impact.
• Do not leave USB memory in direct sunlight or in locations such as
a closed-up automobile. (Storage temperature: 0–50 degrees C).
• Do not allow USB memory to become wet.
• Do not disassemble or modify USB memory.
Add
• When connecting USB memory, position it horizontally with the
external memory connector and insert it without using excessive
force. The external memory connector may be damaged if you use
excessive force when inserting USB memory.
Add
• Do not insert anything other than USB memory (e.g., wire, coins, other
types of device) into the external memory connector. Doing so will
damage the external memory connector.
Add
• Do not apply excessive force to the connected USB memory.
Add
• If you will not be using USB memory for an extended period of time,
close the USB memory cover.
Rear side of the disk
Write
(can write new data onto disk)
Protect
(prevents writing to disk)
Write Protect Tab
RM-700_e.book 10 ページ ２００９年３月１８日 水曜日 午前１１時５分