Filter
Top Products
108
Program operating mode
Page 2 - DK Samples (Drum Programs)
Velocity Switch
This is the velocity value dividing the High and Low layers for
the selected oscillator. Notes struck harder than this value
will be played by the High multisample.
V-Zone Top/Bottom (Velocity Zone)
Here you can specify the velocity range for the selected oscil-
lator.
Note: You cannot set the Bottom Velocity higher than the Top
Velocity, nor the Top Velocity lower than the Bottom Velocity.
0…127 Assigned velocity.
Octave
Use this parameter to adjust the pitch of the selected oscilla-
tor in octave units. The normal octave of the multisample is
“0”.
-2…+1 Octave transposition.
Transpose
Use this parameter to adjust the pitch of the selected oscilla-
tor in semitone steps over a range of ±1 octave.
-12…+12 Transposition in semitones.
Tune
Use this parameter to adjust the pitch of the sample in one-
cent steps (a semitone is 100 cents) over a range of ±1 octave.
-1200…+1200
Fine-tune value in cents.
Delay (ms)
This parameter sets a delay time from the note-on to the real
beginning of the sound. With a setting of KeyOff, the sound
will begin when note-off occurs. This is useful to create
sounds such as the “click” that is heard when a harpsichord
note is released. In this case, set the “Sustain Level” parame-
ter to 0 (see page 14-115).
Key Off The sound will begin when the note is released.
0…5000 Delay time in milliseconds.
PAGE 2 - DK SAMPLES (DRUM PROGRAMS)
This page appears when you edit a Drum Program. Here you
can select a different percussive sample for each layer (High
and Low) on each key.
Key
Key in edit. You can press a key on the keyboard to select a
key.
Assigned
Use this parameter to turn the sample on/off.
Yes The sample is assigned to the selected key.
No The sample is not assigned. The sample
assigned to the next highest assigned key is
used instead.
MS Hi/Lo Bank/Num
Use these parameters to select a different multisample (drum
kit) for each of the High and Low layers. For more informa-
tion, see “MS Hi/Lo Bank/Num” on page 107.
[H/L] Level
These parameters specify the level of each multisample. For
more information, see “[H/L] Level” on page 107.
[H/L] Transpose
These parameters transpose the selected multisample. Use
them to change the pitch of the selected key.
0 No transposition applied.
-64…+63 Transpose value in semitones.
[H/L] Tune
Use these parameters to fine-tune the assigned sample.
0 No fine-tuning.
-99…+99 Fine-tuning value in cents (1/100 of a semi-
tone).
[H/L] Reverse
The multisample will be played in reverse. For more informa-
tion see “[H/L] Reverse” on page 107.
[H/L] Use Offset
These parameters specify the point where the multisample(s)
will begin to play. For more information see “[H/L] Use Off-
set” on page 107.
[H/L] Cutoff
These parameters set the cutoff frequency for the filter
applied to the selected sample.
[H/L] Resonance
These parameters set the resonance for the filter applied to
the selected sample.
[H/L] Attack
These parameters are an offset to the selected sample’s EG
Attack.
[H/L] Decay
These parameters are an offset to the selected sample’s EG
Decay.
Velocity Switch
This is the velocity value dividing the High and Low layers for
the selected sample/key. Notes stricken harder than this value
will be played by the High multisample.
Single Trigger
Use this parameter to set the sample as a single-triggered one.
Yes When the same key (note) is played repeatedly,
the previous note will be stopped before the
new note is triggered, so that they will not
overlap.
No When the same key (note) is played repeatedly,
the previous note will not be stopped before
the new note is triggered.
Receive Note On
Use this parameter to enable/disable the reception of the
Note On (Key On) message.
Yes The Note On message is normally received.
No The Note On message is not received. There-
fore, the corresponding key is muted.
Key: C 2
Assigned: Yes
MS Hi Bank/Num: ROM
BD-SoftRoom 4
DK Samples