Filter
Top Products
208
Effects
Reverb
051: Seq. Delay
(Sequential Delay)
This four-tap delay enables you to select a tempo and rhythm
pattern to set up each tap.
a: BPM, b: Rhythm Pattern
With the tempo specified by the “BPM” parameter (or the
MIDI Clock tempo if “BPM” is set to MIDI), the length of
one beat equals the feedback delay time, and the interval
between taps becomes equal. Selecting a rhythm pattern
will automatically turn the tap outputs on and off. When
“BPM” is set to MIDI, the lower limit of the “BPM” is 44.
Reverb effects
These effects simulate the ambience of reverberation in con-
cert halls.
052: Rev. Hall
This hall-type reverb simulates the reverberation of mid-size
concert halls or ensemble halls.
053: RevSmthHall
(Smooth Hall)
This hall-type reverb simulates the reverberation of larger
halls and stadiums, and creates a smooth release.
054: RevWetPlate
This plate reverb simulates warm (dense) reverberation.
055: RevDryPlate
This plate reverb simulates dry (light) reverberation.
a
BPM
Selects MIDI Clock and assigns tempo
MIDI, 44...240
☞,
b
Rhythm Pattern
Selects a rhythm pattern
– – – ... 3
☞,
c
Tap1 Pan
Sets the panning of Tap1
L, 1...99, R
Tap2 Pan
Sets the panning of Tap2
L, 1...99, R
Tap3 Pan
Sets the panning of Tap3
L, 1...99, R
Tap4 Pan
Sets the panning of Tap4
L, 1...99, R
d
Feedback
Sets the feedback amount
–100...+100
Src Off...Tempo
Selects the modulation source of feedback amount
Amt
Sets the modulation amount of the feedback
–100...+100
e
High Damp [%]
Sets the damping amount in the high range
0...100%
☞ Fx:043
Low Damp [%]
Sets the damping amount in the low range
0...100%
☞ Fx:043
f
Input Level Dmod [%] –100...+100
Sets the modulation amount of the input level
☞ Fx:037,
Src
Selects the modulation source for the input level
Off...Tempo
☞ Fx:037
g
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Delay
Left
Right
Feedback
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Input Level D-mod
High Damp Low Damp
Input Level D-mod
+
Tempo
BPM
BPM
Rythm Pattern
Pan
REVERB
a
Reverb Time [sec]
Sets the reverberation time
0.1...10.0sec
High Damp [%]
Sets the damping amount in the high range
0...100%
b
Pre Delay [msec]
Sets the delay time from the dry sound
0...200msec
☞
Pre Delay Thru [%]
Sets the mix ratio of non-delay sound
0...100%
☞
c
EQ Trim
Table , “Sets the EQ input level,” on page 176
0...100
d
Pre LEQ Gain [dB]
Table , “Sets the gain of Low EQ,” on page 176
–15...+15dB
Pre HEQ Gain [dB]
Table , “Sets the gain of High EQ,” on page 176
–15...+15dB
e
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
EQ Trim
+
EQ Trim
LEQ HEQ
Pre Delay
Reverb
Pre Delay Thru