Filter
Top Products
116
Program operating mode
Page 11 - Filter EG
Decay Time
This parameter specifies the time over which the level will
change from the attack level to the break point level.
Slope Time
This parameter specifies the time over which the level will
change after the decay time has elapsed until the sustain level
is reached.
Release Time
This parameter specifies the time over which the level will
change after note-on occurs until the release level is reached.
Filter EG ‘Level’ modulation
AMS(L) (Alternate Modulation Source)
This parameter selects the source that will control the “Level”
parameters of the filter EG (“AMS (Alternate Modulation
Source) list” on page 123).
Intensity (AMS Intensity)
This parameter specifies the depth and direction of the effect
applied by “AMS”. With a setting of 0, the levels specified by
“Frequency A (Cutoff Frequency A)” will be used.
For example, if “AMS” is Velocity, and you set “Start Level
Swing”, “Attack Level Swing” and “Break Level Swing” to +
and set “Intensity” to a positive (+) value, the EG levels will
rise as you play more strongly. If “Intensity” is set to a nega-
tive (–) values, the EG levels will fall as you play more
strongly.
-99…+99 Intensity value.
Start Level Swing
This parameter specifies the direction in which “AMS” will
affect “Start Level”. When “Intensity” has a positive (+)
value, a setting of + for this parameter will allow “AMS” to
raise the EG level, and a setting of – will allow “AMS” to lower
the EG level. With a setting of 0 there will be no change.
Attack Level Swing
This parameter specifies the direction in which “AMS” will
affect “Attack Level”. When “Intensity” has a positive (+)
value, a setting of + for this parameter will allow “AMS” to
raise the EG level, and a setting of – will allow “AMS” to lower
the EG level. With a setting of 0 there will be no change.
Break Level Swing
This parameter specifies the direction in which “AMS” will
affect “Break Point Level”. When “Intensity” has a positive
(+) value, a setting of + for this parameter will allow “AMS”
to raise the EG level, and a setting of – will allow “AMS” to
lower the EG level. With a setting of 0 there will be no
change.
Filter EG ‘Time’ modulation
AMS1/2(T)
Use this parameter to select the source that will control the
“Time” parameters of the filter EG. See “AMS (Alternate
Modulation Source) list” on page 123.
Intensity
This parameter specifies the depth and direction of the effect
that “AMS1/2(T)” will have.
For example, if “AMS1/2(T)” is set to FltKTr +/+, the EG
“Time” parameters will be controlled by the Keyboard Track-
ing settings. With positive (+) values of this parameter, posi-
tive (+) values of “Ramp” will lengthen the EG times, and
negative (–) values of “Ramp” will shorten the EG times. The
direction of change is specified by “Attack Time Swing”,
“Decay Time Swing”, “Slope Time Swing”, and “Release
Time Swing”.
With a setting of 0, the times specified by “Frequency A (Cut-
off Frequency A)” will be used.
If “AMS1/2(T)” is set to Velocity, positive (+) values of this
parameter will cause EG times to lengthen as you play more
strongly, and negative (–) values will cause EG times to
shorten as you play more strongly.
-99…+99 Intensity value.
Attack Time Swing
This parameter specifies the direction in which “AMS1/2(T)”
will affect the attack time. With positive (+) values of “Inten-
sity”, setting this parameter to + will allow AMS to lengthen
the time, and setting this parameter to – will allow AMS to
shorten the time. With a setting of 0 there will be no change.
Decay Time Swing
This parameter specifies the direction in which “AMS1/2(T)”
will affect the decay time. With positive (+) values of “Inten-
sity”, setting this parameter to + will allow AMS to lengthen
the time, and setting this parameter to – will allow AMS to
shorten the time. With a setting of 0 there will be no change.
Slope Time Swing
This parameter specifies the direction in which “AMS1/2(T)”
will affect the slope time. With positive (+) values of “Inten-
sity”, setting this parameter to + will allow AMS to lengthen
the time, and setting this parameter to – will allow AMS to
shorten the time. With a setting of 0 there will be no change.
Release Time Swing
This parameter specifies the direction in which “AMS1/2(T)”
will affect the release time. With positive (+) values of “Inten-
sity”, setting this parameter to + will allow AMS to lengthen
the time, and setting this parameter to – will allow AMS to
shorten the time. With a setting of 0 there will be no change.
Filter 1 EG changes (level) (AMS = Velocity, Intensity = a positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Softly played note with Start Level
Swing, Attack Level Swing, and
Break Level Swing set to +
Strongly played note with Start
Level Swing, Attack Level Swing,
and Break Level Swing set to +
Strongly played note with Start
Level Swing, Attack Level Swing,
and Break Level Swing set to –
Filter 1 EG changes (Time) (AMS = Velocity, Intensity = a positive (+) value)
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
Softly played note with Attack,
Decay, Slope and Release
Level Swings set to +
Strongly played note with
Attack, Decay, Slope and
Release Level Swings set to +
Strongly played note with
Attack, Decay, Slope and
Release Level Swings set to –