Filter
Top Products
177
Effects
Filter/Dynamic
Adjust the output level using the “Gain Adjust” parame-
ter, since compression causes the entire level to be
reduced.
d: Attack, d: Release
These parameters set the attack time and release time. A
higher attack time will cause the compression to be
applied more slowly.
f: Side PEQ Insert, g: Side PEQ Cutoff [Hz], g: Q, g: Gain
[dB]
These parameters are used to set the EQ applied to the
trigger signal.
The Limiter determines whether the compression is
applied or not, based on the post-EQ trigger signal. Set-
ting the equalizer allows you to set the Limiter to respond
to any frequency band.
f: Trigger Monitor
Setting this parameter On will cause the trigger signal to
be output, instead of the effect sound. Use this parameter
to check the trigger signal with EQ applied.
Usually, set this to Off.
004: MBandLimit
(Multiband Limiter)
This effect applies the Limiter to the low range, mid range,
and high range of the input signal. You can control dynamics
for each range to adjust the sound pressure of the low range,
mid range, and high range in a different way from the EQ.
e: Low Offset [dB], f: Mid Offset [dB], g: High Offset [dB]
These parameters set the gain of the trigger signal.
For example, if you do not want to apply compression to
the high range, reduce the “High Offset” value down
below the “Threshold” level. In this way, the high range
limiter will not respond, and compression will not be
applied.
Input Level
Output Level
Threshold
Ratio=1.0 : 1
Ratio=2.0 : 1
Ratio=4.0 : 1
Ration=Inf : 1
Louder
Louder
Time
Level
Threshold
Ratio=Inf : 1
Ratio=2.0 : 1
Ratio=4.0 : 1
Dry
Ratio=1.0 : 1
Limiter - Threshold / Ratio
Threshold
Ratio=Inf : 1
Attack=1
Release=1
Ratio=Inf : 1
Attack=100
Release=100
Dry
Wet
Wet
Release
Attack
Limiter - Attack / Release
a
Ratio 1.0:1...50.0:1, Inf:1
Sets the signal compression ratio
☞ Fx:003
b
Threshold [dB] –40...0dB
Sets the level above which the compressor is applied
☞ Fx:003
c
Attack
Sets the attack time
1...100
☞ Fx:003
d
Release
Sets the release time
1...100
☞ Fx:003
e
Low Offset [dB]
Gain of the low-range trigger signal
–40...0dB
☞
f
Mid Offset [dB]
Gain of the mid-range trigger signal
–40...0dB
☞
g
High Offset [dB]
Gain of the high-range trigger signal
–40...0dB
☞
h
Gain Adjust [dB] –Inf, –38...+24dB
Sets the output gain
☞ Fx:003,
Src
Selects the modulation source for the output gain
Off...Tempo
Amt
Sets the modulation amount of the output gain
–63...+63
i
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Gain Adjust
Mid Offset
Low Offset
High Offset
Limiter
Envelope - Control
Envelope - Control
Envelope - Control
Limiter
Limiter
Low
Mid
High
Band-Pass Filters
+