Filter
Top Products
189
Effects
Pitch/Phase Mod.
The “Src” parameter selects the source that starts the
envelope generator. If you select, for example, Gate, the
envelope generator will start when the note-on message
is received.
When “Sweep Mode” = D-mod, the modulation source
can control the flanger directly. Select the modulation
source using the “Src” parameter.
The effect is off when a value for the modulation source speci-
fied for the “Src” parameter is smaller than 64, and the effect is
on when the value is 64 or higher. The Envelope Generator is
triggered when the value changes from 63 or smaller to 64 or
higher.
d: EG Attack, d: EG Decay
Attack and Decay speed are the only adjustable parame-
ters on this EG.
023: Phaser
(Stereo Phaser)
This effect creates a swell by shifting the phase. It is very
effective on electric piano sounds. You can add spread to the
sound by offsetting the phase of the left and right LFOs from
each other.
g: Resonance, h: Wet/Dry
The peak shape of the positive and negative Feedback
value is different. The harmonics will be emphasized
when the effect sound is mixed with the dry sound, if you
set a positive value for both “Resonance” and “Wet/Dry”,
and if you set a negative value for both “Resonance” and
“Wet/Dry”.
g: High Damp [%]
This parameter sets the amount of damping of the reso-
nance in the high range. Increasing the value will cut
high-range harmonics.
a
LFO Waveform
Selects LFO Waveform
Triangle, Sine
LFO Shape –100...+100
Determines how much the LFO waveform is changed
☞ Fx:020
b
LFO Phase [degree] –180...+180
Sets the LFO phase difference between the left and right
☞ Fx:010
c
LFO Frequency [Hz] 0.02...20.00Hz
Sets the LFO speed
☞ Fx:009,
Src
Selects the modulation source of LFO speed
Off...Tempo
Amt –20.00...+20.00Hz
Sets the modulation amount of LFO speed
Left
Right
Resonance
LFO Shape
LFO Phase
LFO: Tri / Sine
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
Phaser
Phaser
d
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using the
tempo and notes
☞ Fx:009,
BPM MIDI, 40...240
Selects MIDI Clock and assigns tempo
☞ Fx:009
Base Note
Selects the type of notes that specify the LFO speed ☞ Fx:009
Times x1...x16
Sets the number of notes that specify the LFO speed
☞ Fx:009
e
Manual
Sets the frequency to which the effect is applied
0...100
f
Depth
Sets the depth of LFO modulation
0...100
Src Off...Tempo
Selects the modulation source for the LFO modulation depth
Amt –100...+100
Sets the modulation amount of the LFO modulation depth
g
Resonance
Sets the resonance amount
–100...+100
☞
High Damp [%] 0...100%
Sets the resonance damping amount in the high range
☞
h
Wet/Dry –Wet...–1:99, Dry, 1:99...Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
☞ Fx:010,
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100