Filter
Top Products
193
Effects
Pitch/Phase Mod.
a: Control Mode, e: Voice1: Resonance, h: Voice2:
Resonance
This parameter determines the resonance intensity.
When “Control Mode” = Manual, the “Resonance”
parameter sets the intensity of resonance. If the “Reso-
nance” parameter has a negative value, harmonics will be
changed, and resonance will occur at a pitch one octave
lower.
When “Control Mode” = LFO, the intensity of resonance
varies according to the LFO. The LFO sways between posi-
tive and negative values, causing resonance to occur
between specified pitches an octave apart in turn.
When “Control Mode” = D-mod, the resonance is con-
trolled by the dynamic modulation source. If JS X or Rib-
bon is assigned as the modulation source, the pitch an
octave higher and lower can be controlled, similar to
when LFO is selected for Control Mode.
a: LFO/D-mod Invert
When “Control Mode” = LFO or D-mod, the controlled
phase of either Voice 1 or 2 will be reversed. When the
resonance pitch is set for Voice 1 (Resonance has a positive
value), Voice 2 will resonate at a pitch an octave below
(Resonance has a negative value).
d: Voice1: Pitch, d: Fine [cent], g: Voice2: Pitch, g: Fine
[cent]
The Pitch parameter specifies the pitch of resonance by
note name. The “Fine” parameter allows for fine adjust-
ment in steps of cents.
e: High Damp [%], h: High Damp [%]
This parameter sets the damping amount of resonant
sound in the high range. Lower values will make a metal-
lic sound with a higher range of harmonics.
030: Doppler
This effect simulates the “Doppler effect” of a moving sound
with a changing pitch, similar to the siren of an passing
ambulance. Mixing the effect sound with the dry sound will
create a unique chorus effect.
a: LFO Mode, a: Src, b: LFO Sync
The “LFO Mode” parameter switches LFO operation
mode. When Loop is selected, the Doppler effect will be
created repeatedly. If “LFO Sync” is set to On, the LFO will
be reset when the modulation source specified with the
“Src” parameter is turned on.
When “LFO Mode” is set to 1-Shot, the Doppler effect is
created only once when the modulation source specified
in the “Src” field is turned on. At this time if you do not
set the “Src” parameter, the Doppler effect will not be
created, and no effect sound will be output.
The effect is off when a value for the modulation source speci-
fied for the “Src” parameter is smaller than 64, and the effect is
on when the value is 64 or higher. The Doppler effect is trig-
gered when the value changes from 63 or smaller to 64 or
higher.
e: Pitch Depth
With the Doppler effect, the pitch is raised when the
sound approaches, and the pitch is lowered when the
sound goes away. This parameter sets this pitch variation.
f: Pan Depth
This parameter sets the width of the stereo image of the
effect sound. With larger values, the sound seems to come
and go from much further away. With positive values, the
sound moves from left to right; with negative values, the
sound moves from right to left.
j
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
a
LFO Mode
Switches LFO operation mode
Loop, 1-Shot
☞,
Src Off...Tempo
When LFO Mode is set to 1-Shot, this modulation source triggers the LFO
☞
b
LFO Sync Off, On
Switches between LFO reset on and off when LFO Mode is set to Loop
☞
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Pan Depth
D
-mod
+
Trigger
LFO Mode = 1-Shot
Doppler
LFO
c
LFO Frequency [Hz] 0.02...20.00Hz
Sets the LFO speed
☞ Fx:009,
Src
Selects the modulation source of LFO speed
Off...Tempo
Amt –20.00...+20.00Hz
Sets the modulation amount of LFO speed
d
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using the
tempo and notes
☞ Fx:009,
BPM
Selects MIDI Clock and assigns tempo
MIDI, 40...240
☞ Fx:009
Base Note
Selects the type of notes that specify the LFO speed ☞ Fx:009
Times x1...x16
Sets the number of notes that specify the LFO speed
☞ Fx:009
e
Pitch Depth
Sets the pitch variation of the moving sound
0...100
☞,
Src
Selects the modulation source of pitch variation
Off...Tempo
Amt
Sets the modulation amount of pitch variation
–100...+100
f
Pan Depth
Sets the panning of the moving sound
–100...+100
☞,
Src
Selects the modulation source of panning
Off...Tempo
Amt
Sets the modulation amount of panning
–100...+100
g
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Pitch
Higher
Doppler - Pitch / Pan Depth
Lower
Original Pitch
Left
Center
Right
Pitch Depth
Pan Depth
< < < < < <<<<<< >>>>>> > > > > >
VolumeLouder
Louder
Pan Depth
= (–) value
Pan Depth
= (+) value