Filter
Top Products
Appendix
204
MIDI data format
1. Functions
1.1. Scene Change
The settings of the [MIDI PROGRAM CHANGE TABLE] specify the
scene that is recalled when a Program Change message is received.
The settings of the [MIDI PROGRAM CHANGE TABLE] specify the
program number that is transmitted when a scene is recalled. If more
than one program number has been assigned to that scene memory
number, the lowest-numbered program number will be transmitted.
1.2. MMC Control
These messages allow basic recorder operations such as STOP/PLAY/
REC/LOCATE.
If you select the MIDI SETUP menu item MMC MASTER, MMC
commands will be transmitted according to the operation of the
transport. If you select MMC SLAVE, the internal recorder will oper-
ate according to the received MMC commands.
1.3. Effect Control
Depending on the type of effect, note-on/off messages can be used
for control.
These settings are made for the parameters of each effect.
1.4. MIDI Clock transmission
If you set MIDI OUT to MIDI CLOCK, MIDI clock messages can be
transmitted during playback or recording.
In MIDI Clock transmission mode, Song Position Pointer and Start/
Stop/Continue commands will also be issued, and during playback
or recording, MIDI Clock will be transmitted according to the MIDI
Tempo Map.
1.5. MTC transmission (MTC Master)
If you set MIDI OUT to MTC, MTC can be transmitted during play-
back or recording.
1.6. MTC reception (MTC Slave)
If you set MTC MODE to SLAVE, the internal recorder will operate
in synchronization with MTC messages received from the MIDI IN
connector.
1.7. Realtime control of parameters
Control changes can be used to send/receive internal parameters in
realtime.
1.8. Transmission of scene memories or data
The bulk dump function can be used to send data to another device,
or copy settings from another device to the AW16G.
1.9. MIDI Remote
The faders, SEL keys, and RTZ / FF / REW / STOP / PLAY / REC keys
can be used to control an external MIDI device.
In PRESET mode, operating the above controllers will transmit
MIDI data according to the preset settings of the AW16G.
In USER mode, operating the above controllers will transmit the
MIDI data that you specify.
2. MIDI data flow diagram
3. AW16G settings and operation
3.1. MIDI Setup
Set basic MIDI operation.
3.1.1. MIDI OUT
Specify the function of the MIDI OUT connector.
3.1.2. MMC MODE
Select whether the AW16G will be the MMC MASTER or SLAVE.
3.1.3. MMC Dev.
Specify the ID number that will be used when transmitting or receiv-
ing MMC commands.
3.1.4. MTC SYNC MODE
Select whether the AW16G will be the MTC MASTER or SLAVE.
3.1.5. MTC SYNC AVERAGE
When the AW16G is functioning as a MTC SLAVE, this setting speci-
fies how it will follow the MTC data. Set this to 0 if the incoming
MTC data has a highly accurate timing; set this to 1 or 2 if the timing
of the incoming MTC data is not as accurate (such as when receiving
MTC from a software sequencer).
3.1.6. MTC SYNC OFFSET
When the AW16G is functioning as a MTC SLAVE, this setting adds
an offset to the received MTC data. The received time code value
shifted by this amount will correspond to the location indicated by
the internal time code of the AW16G.
3.1.7. MIDI Tx Ch
This sets the MIDI channel that will normally be used.
However, transmission in response to a request will occur on the
Receive Channel, in order to specify the device that transmitted the
request.
3.1.8. MIDI Rx Ch
This sets the MIDI channel that will be used for reception. If this is
set to ALL, data of all MIDI channels will be receive d.
MTC (MTC Slave)
PROGRAM CHANGE (Scene Recall)
CONTROL CHANGE (Parameter Edit)
BULK DUMP / BULK DUMP Request
MMC (Transport Control)
Channel Message / Exclusive Message
(MIDI REMOTE Learn)
MTC SLAVE
PGM CHG
CTRL CHG
RX DISABLE
MMC SLAVE
LEARN
PROGRAM CHANGE
CONTROL CHANGE
BULK DUMP /
BULK DUMP Request
MMC
MTC
MIDI CLOCK
PGM CHG
CTRL CHG
TRANSMIT/REQUEST
MMC MASTER
MIDI OUT (MTC)
MIDI OUT (CLK)
MIDI OUT (MIDI)
MIDI OUT (THRU)
MIDI IN
MIDI OUT
REMOTE Transport
REMOTE Fader/Sel
SW1
SW2
SW3
SW4
SW1 REMOTE OFF
SW2 REMOTE ON(Remote)
SW3 REMOTE ON
SW4 REMOTE OFF or REMOTE ON(Normal)
SW4
NOTE ON/OFF (Effect Control)
EFF MIDI