Filter
Top Products
104
Editing a Sample
This section explains how you can edit a sample that you sampled/
imported
Editing is performed in sample memory—a memory area dedicated
to samples (p. 25).
Select a sample from the list.
1.
Press [SAMPLE EDIT <-> LIST] to access the SAMPLE LIST
screen.
fig.SampleList
2.
Press or to select the group that contains the
desired sample.
•
PRST:
preset samples
•
USER:
user samples
•
CARD:
samples stored on a memory card
* You cannot edit preset samples.
3.
Use the VALUE dial, [INC] [DEC], or to select a
sample.
* You can press [F6 (PREVIEW)] to audition the selected sample.
4.
Press [ENTER] or [SAMPLE EDIT <-> LIST].
The SAMPLE EDIT screen appears.
Here’s how you can load a sample from the user area, a memory
card, or a preset into sample memory.
1.
Press [SAMPLE EDIT <-> LIST] to access the SAMPLE LIST
screen.
2.
Press or to select the group that contains the
desired sample.
3.
Use the VALUE dial, [INC] [DEC], or to select a
sample.
If you want to load two or more samples, press [F2 (MARK)] to
add a check mark (
✔
) to the samples that you want to select.
To remove the check mark from a selected sample, select and
press [F2 (MARK)] again.
If you hold down [SHIFT] and press [F4 (SET ALL)], a check
mark will be added to all samples of the selected group.
If you hold down [SHIFT] and press [F3 (CLR ALL)], check
marks will be removed from all selected samples.
4.
Press [F5 (UTILITY)], and then press [F5 (LOAD)].
A message will ask you for confirmation.
5.
Press [F6 (EXEC)] to load the sample.
To cancel, press [F5 (CANCEL)].
* You can also perform this operation from the SAMPLE LIST or
SAMPLE EDIT screen by pressing [MENU] and selecting “Load
Sample.”
Here’s all samples in the user memory and memory card can be
loaded.
When you execute Load All Samples, all unsaved samples
will be erased.
* If the total size of the data in the user bank and card bank exceeds the
size of memory, the samples of the user bank will be loaded first. At
this time, as many card bank samples as possible will be loaded,
starting from the lowest-numbered sample.
1.
From the SAMPLE LIST screen, press [F5 (UTILITY)].
2.
Press [F2 (LOAD ALL)].
A message will ask you for confirmation.
3.
Press [F6 (EXEC)] to execute.
To cancel, press [F5 (CANEL)].
* You can also perform this operation from the SAMPLE LIST screen
by pressing [MENU] and selecting “3. Load All Samples.”
Sample List
Selecting a Sample
The sample list shows the current state of
the samples.
fig.SampleState
N (New): This is a sample that you sampled. It will be lost
when you turn off the power. The same is true for
samples imported as WAV/AIFF.
U (Unload): The sample has been saved, but not loaded into
sample memory.
E (Edit): This is a sample that you loaded or sampled and
are editing. Your edits will be lost when you turn
off the power. If you want to keep them, you must
Write the sample. Save this data as necessary.
If Load User Samples at Startup (p. 193) is turned off, samples
will not be loaded into memory when you turn on the power. In
this case, you will need to load samples into memory yourself.
If you have unload a sample from sample memory, you will
also need to load it again before you can re-select that sample.
Loading a Sample
Loading all Samples
Fantom-Xa_e.book 104 ページ ２００４年１０月２２日 金曜日 午後２時３分